Read Sony DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) Service Manual online
1-5
ENGLISH
JAPANESE
ENGLISH
JAPANESE
DCR-DVD510E/DVD910/DVD910E/
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
HDR-UX9E/UX10/UX10E/UX19E/UX20/UX20E_L2
Address
7430
F946
F948
F948
F946
F948
F948
7430
1-5-2. E:62:11 [Shift Lens Overheating (Pinch)] Occurred
Connect by the SeusEX and perform the following process.
Order
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Block
11
11
11
11
11
11
11
11
Page
80
8E
8E
8E
8E
8E
8E
80
Procedure
Write the data. (After it starts, set it before caution is displayed.)
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Write the data. (Note 1)
Write the data.
Write the data.
Check if the shift lens moves while setting the order 2 to 7. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
replace the lens block (Note 2). When the shift lens moved, proceed to the order 10.
While setting the order 2 to 7, measure with an oscilloscope the output voltage of R5526 in
the periphery of IC5501 on the LD-233 board to check the output voltage varies.
the periphery of IC5501 on the LD-233 board to check the output voltage varies.
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 12.
varied, proceed to the order 12.
Turn the power OFF.
While measuring with an oscilloscope the output voltage of R5549 in the periphery of IC5501
on the LD-233 board, turn the power ON to check that the output voltage immediately after
the power on change as shown in Fig. 2.
on the LD-233 board, turn the power ON to check that the output voltage immediately after
the power on change as shown in Fig. 2.
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-521 board) periphery.
change as shown in Fig. 2, inspect the camera control circuit (IC1301 of VC-521 board) periphery.
Note 1:
Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address: F948, data: 00, and then retry.
Note 2:
When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
Data
01
F0
01
00
10
01
00
00
Click on the first or last page to see other DCR-DVD510E / DCR-DVD910 / DCR-DVD910E / HDR-UX10 / HDR-UX10E / HDR-UX19E / HDR-UX20 / HDR-UX20E / HDR-UX9E (serv.man2) service manuals if exist.