Read Sony CPD-L181 Service Manual online
1-5
Customizing Your Monitor
12
Horizontal
Frequency*
Frequency*
Vertical
Frequency*
Frequency*
BRIGHTNESS
26
48. 4kHz / 60Hz
CONTRAST
26
48. 4kHz / 60Hz
Horizontal
Frequency*
Frequency*
Vertical
Frequency*
Frequency*
For vertical adjustment, select V using the ˘/≥
buttons and adjust the position using the +/–
buttons.
+ . . . to move the picture up
– . . . to move the picture down
buttons and adjust the position using the +/–
buttons.
+ . . . to move the picture up
– . . . to move the picture down
5
When you have finished, click [END] on the screen to
turn off the test pattern.
turn off the test pattern.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button twice.
To close the OSD, press the MENU button twice.
Adjusting the Picture Brightness
Once the brightness is adjusted, it will be stored in memory
for all input signals received.
for all input signals received.
1
Press the ¨ (brightness) ˘ button.
The BRIGHTNESS OSD appears.
The BRIGHTNESS OSD appears.
2
Press the +/– buttons.
+ . . . for more brightness
– . . . for less brightness
– . . . for less brightness
The OSD automatically disappears after about 3 seconds.
*
The horizontal and vertical frequencies for the received input
signal appear in the BRIGHTNESS OSD.
signal appear in the BRIGHTNESS OSD.
If the screen is too bright when using the monitor in a
dark room
dark room
Decrease the BACKLIGHT (page 15).
CENTER
H
V
V
26
Adjusting the Contrast
Once the contrast is adjusted, it will be stored in memory for
all input signals received.
all input signals received.
1
Press the > (contrast) ≥ button.
The CONTRAST OSD appears.
The CONTRAST OSD appears.
2
Press the +/– buttons.
+. . . for more contrast
– . . . for less contrast
– . . . for less contrast
The OSD automatically disappears after about 3 seconds.
*
The horizontal and vertical frequencies for the received input
signal appear in the CONTRAST OSD.
signal appear in the CONTRAST OSD.
Changing the Picture Size
According to the Signal
According to the Signal
The monitor is set at the factory to display the picture on the
screen in full, irrespective of the picture’s mode or
resolution. You can also view the picture at its actual aspect
ratio or resolution. Note that 1280
screen in full, irrespective of the picture’s mode or
resolution. You can also view the picture at its actual aspect
ratio or resolution. Note that 1280
×
1024 resolution signals
fill the entire screen and ZOOM is not possible.
Once the zoom is set, it will be stored in memory for the
current input signal.
Once the zoom is set, it will be stored in memory for the
current input signal.
FULL 1
The input signal is displayed on the screen in full,
irrespective of the picture’s mode or resolution.
irrespective of the picture’s mode or resolution.
FULL 2
The input signal is displayed on the screen at its actual
aspect ratio. Therefore, black bands may appear at the
top and bottom of the picture depending on the signal.
aspect ratio. Therefore, black bands may appear at the
top and bottom of the picture depending on the signal.
REAL
The input signal is displayed on the screen at its actual
resolution. (Sub-SXGA signals are displayed at the center
of the screen surrounded by black frame.)
resolution. (Sub-SXGA signals are displayed at the center
of the screen surrounded by black frame.)
13
Getting Started
Customizing Your Monitor
F
D
ES
GB
I
MENU
EXIT
PHASE
PITCH
CENTER
PITCH
CENTER
ZOOM/SMOOTHING
COLOR
LANGUAGE
OPTION
LANGUAGE
OPTION
MENU
OK
MENU
MENU
ZOOM/SMOOTHING
ZOOM
SMOOTHING
SMOOTHING
FULL1
FULL2
REAL
FULL2
REAL
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ˘/≥ buttons to select ZOOM/SMOOTHING,
and press the MENU button again.
The ZOOM/SMOOTHING OSD appears.
and press the MENU button again.
The ZOOM/SMOOTHING OSD appears.
3
Press the ˘/≥ buttons to select ZOOM.
4
Press the +/– buttons to select the desired mode.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button twice.
To close the OSD, press the MENU button twice.
To display the picture on the screen in full
Select “FULL 1” in step 4.
If the picture displayed at FULL 1 or FULL2
mode is not smooth
mode is not smooth
Use the picture smoothing function. The smoothing effect
becomes stronger in the order of TEXT n STANDARD n
GRAPHICS. Note that 1280
becomes stronger in the order of TEXT n STANDARD n
GRAPHICS. Note that 1280
×
1024 resolution signals are
shown only in REAL mode and SMOOTHING is not
possible.
Once the smoothing is set, it will be stored in memory for
the current input signal.
possible.
Once the smoothing is set, it will be stored in memory for
the current input signal.
STANDARD
Standard smoothing effect (factory preset smoothing
effect).
effect).
TEXT
To make the characters appear clear. (This mode is suited
for text-based applications.)
for text-based applications.)
GRAPHICS
To make the pictures appear clean. (This mode is suited
for CD-ROM software such as photo images or
illustrations.)
for CD-ROM software such as photo images or
illustrations.)
1
Press the MENU button.
The MENU OSD appears.
The MENU OSD appears.
2
Press the ˘/≥ buttons to select ZOOM/SMOOTHING,
and press the MENU button again.
The ZOOM/SMOOTHING OSD appears.
and press the MENU button again.
The ZOOM/SMOOTHING OSD appears.
3
Press the ˘/≥ buttons to select SMOOTHING.
4
Press the +/– buttons to select the desired mode.
The OSD automatically disappears after about 30 seconds.
To close the OSD, press the MENU button twice.
To close the OSD, press the MENU button twice.
MENU
MENU
EXIT
PHASE
PITCH
CENTER
PITCH
CENTER
ZOOM/SMOOTHING
COLOR
LANGUAGE
OPTION
LANGUAGE
OPTION
MENU
OK
MENU
ZOOM/SMOOTHING
ZOOM
SMOOTHING
SMOOTHING
FULL1
FULL2
REAL
FULL2
REAL
ZOOM/SMOOTHING
ZOOM
SMOOTHING
SMOOTHING
FULL1
FULL2
REAL
FULL2
REAL
ZOOM/SMOOTHING
ZOOM
SMOOTHING
SMOOTHING
STANDARD
TEXT
GRAPHICS
TEXT
GRAPHICS
Click on the first or last page to see other CPD-L181 service manuals if exist.