Read Sony CPD-L181 Service Manual online
1-2
6
Getting Started
IBM PC/AT or
compatible
computer
compatible
computer
HD15 video
signal cable
(supplied)
signal cable
(supplied)
to monitor output
to
…
1 or
…
2
to a power outlet
Power cord
(supplied)
(supplied)
HD15 video
signal cable
(supplied)
signal cable
(supplied)
Setup
Before using this monitor, check that the following items are
included in your carton:
• LCD monitor (1)
• Rear cover (1)
• Power cord (1)
• HD15 video signal cable (1)
• Macintosh adapter (1)
• Windows
included in your carton:
• LCD monitor (1)
• Rear cover (1)
• Power cord (1)
• HD15 video signal cable (1)
• Macintosh adapter (1)
• Windows
Monitor Information Disk/Utility Disk (1)
• Macintosh Utility Disk (1)
• Warranty card (1)
• These operating instructions (1)
• Warranty card (1)
• These operating instructions (1)
Step 1: Connect the monitor to the
computer
computer
Turn off the monitor and computer before connecting.
Connecting to an IBM PC/AT or compatible
computer
computer
If your PC system is not compatible with Plug &
Play (DDC2B and DDC2Bi)
Play (DDC2B and DDC2Bi)
This monitor uses the No. 9 pin in the video signal connector for
Plug & Play (DDC2B and DDC2Bi) compatibility. See page 20 for
the location of the No. 9 pin.
• If your computer accepts the No. 9 pin, use the supplied HD15
Plug & Play (DDC2B and DDC2Bi) compatibility. See page 20 for
the location of the No. 9 pin.
• If your computer accepts the No. 9 pin, use the supplied HD15
video signal cable.
• If your computer does not accept the No. 9 pin, please consult
your dealer for advice on obtaining an HD15 adapter.
to monitor output
to AC IN
Connecting to a Macintosh
Use the supplied Macintosh adapter.
*
Connect the supplied Macintosh adapter to the computer before
connecting the cable. This adapter is compatible with Macintosh
LC, Performa, Quadra, Power Macintosh and Power Macintosh
G3 series computers (sold before January, 1999). If you are
connecting to a Power Macintosh G3 series that sold after
January 1999, you will need a different adapter (not supplied).
Macintosh II series and some older versions of PowerBook
models may need an adapter with micro switches (not
supplied).
connecting the cable. This adapter is compatible with Macintosh
LC, Performa, Quadra, Power Macintosh and Power Macintosh
G3 series computers (sold before January, 1999). If you are
connecting to a Power Macintosh G3 series that sold after
January 1999, you will need a different adapter (not supplied).
Macintosh II series and some older versions of PowerBook
models may need an adapter with micro switches (not
supplied).
Step 2: Connect the power cord
With the monitor and computer switched off, connect one
end of the AC power cord to the monitor and the other end
to a power outlet.
end of the AC power cord to the monitor and the other end
to a power outlet.
to
…
1 or
…
2
Macintosh adapter
(supplied)*
(supplied)*
Macintosh or
compatible computer
compatible computer
7
Getting Started
Getting Started
F
D
ES
GB
I
Step 3: Attaching the rear cover
After connecting the computer and power cord, attach the
supplied rear cover.
Make sure that you keep the screen upright when attaching
the rear cover.
supplied rear cover.
Make sure that you keep the screen upright when attaching
the rear cover.
1
Hook the computer cable and power cord.
2
Press the top of the rear cover against the top of the
part for attaching the cover, and then push the rear
cover in.
part for attaching the cover, and then push the rear
cover in.
3
Turn the screw to fasten the rear cover.
Unlocked
Locked
Use of the Tilt
Use the tilt feature to adjust the monitor to the desired angle
within 30° upward, and 45° to the left or right.
To turn the monitor, hold it at the bottom with both hands
as illustrated below.
within 30° upward, and 45° to the left or right.
To turn the monitor, hold it at the bottom with both hands
as illustrated below.
30
°
45
°
45
°
1
2
Click on the first or last page to see other CPD-L181 service manuals if exist.