CPD-220AS - Sony Monitor Service Manual (repair manual). Page 6

Read Sony CPD-220AS Service Manual online

– 6 –
10
GB
Getting Started
Before using this display, please make sure that the following items are included
in your package:
• Multimedia computer display (1)
• Warranty card (1)
• Operating instruction manual (1)
• Windows 95 Monitor Information Disk and its instruction manual (1)
 Tip
This display will sync with any IBM or compatible system equipped with VGA
1)
 or greater graphics
capability. Although this display will sync to other platforms running at horizontal frequencies
between 30 and 70 kHz, including Macintosh
2)
 and Power Macintosh systems, a cable adapter is
required. Please consult Sony Technical Support for advice on which adapter is suitable for your
needs.
1)
VGA is a trademark of IBM Corporation.
2)
Macintosh is a trademark of Apple Computer Inc.
Installation
p
 Step 1: Connect the computer
With the computer switched off, connect the video signal cable to the display
(VGA) connector on your computer.  If your computer supports the DDC plug-
and-play standard, this connection will enable the DDC communication between
the display and the computer.
Also the video signal cable is combined with audio and microphone cables.  If
your computer is equipped with sound capability, connect the audio and
microphone plugs to appropriate jacks located on your computer.
If you use a USB (universal serial bus) device, connect the USB device to the
USB downstream jack and the PC to the USB upstream jack.
Getting Started
11
GB
Getting Started
p
 CPD-120AS
p
 CPD-220AS
Note on handling the video signal cable
Do not touch the pins of the video signal cable.
Note on USB ports
USB ports are included to provide state-of-the-art technology. Until USB support is
available at the operating system level, you must supply drivers to use USB devices.
You can upgrade your operating system to a version that supports USB at the
operating system level once a version becomes available.
See the manual that came with your USB device for more information on setting it up
and using it.
Continued to the next page 
Computer
Red (to microphone
connector)
Blue (to display
connector)
Green (to speaker
connector)
 to 
Computer
Red (to microphone
connector)
Blue (to display
connector)
Green (to speaker
connector)
 to 
 to USB port
 to USB port
12
GB
Getting Started
to a power outlet
Power cord (supplied)
p
 Step 2: Connect the power cord
With the display switched off, connect the power cord to the display and the
other end to a power outlet.
p
 CPD-120AS
p
 CPD-220AS
p
 Step 3: Turn on the display and computer.
p
 Step 4: If necessary...
Adjust the user controls according to your personal preference.
The installation of your display is complete. Enjoy your display.
to a power outlet
Power cord (supplied)
13
GB
Vertical
Frequency
70 Hz
60 Hz
85 Hz
60 Hz
75 Hz
75 Hz
85 Hz
47 Hz (95 Hz interlace)
60 Hz
60 Hz
Preset and user modes
The Multiscan CPD-120AS/220AS display has factory preset modes for the 10
most popular industry standards for true “plug and play” capability.
For less common modes, its Digital Multiscan Technology will perform all of
the complex adjustments necessary to ensure a high quality picture for any
timing between 30 and 70 kHz.
Note for Windows
® 
95 users
Install the new model information of the Sony computer display from “Windows 95 Monitor
Information disk” into your PC.  (To install the file, refer to the attached “About the Windows 95
Monitor Infomration Disk”.)
This display complies with “VESA DDC,” the standards of Plug & Play. If your PC/graphic board
complies with DDC, select “Plug & Play Display (VESA DDC)” or this display’s model name (CPD-
120AS/220AS) as “Display type” from “Control Panel” on Windows 95. Some PC/graphic boards
do not comply with DDC. Even if they comply with DDC, that may have some problems on
connecting this display. In this case, select this display’s model name (CPD-120AS/220AS) as
“Display type” on Windows 95.
Windows
®
 is a registered trademark of Microsoft Corporation in the United States and other
countries.
Note on recommended horizontal timing conditions
Horizontal sync width should be more than 1.0 µsec.
Horizontal blanking width should be more than 3.6 µsec.
Continued to the next page 
Using Your  Display
Using Your Display
Resolution
 (dots 
×
 lines)
640 
×
 400
640 
×
 480
640 
×
 480
800 
×
 600
800 
×
 600
1024 
×
 768
1024 
×
 768
1152 
×
 864
1152 
×
 864
1280 
×
 1024
Horizontal
Frequency
31.5 kHz
31.5 kHz
43.3 kHz
37.9 kHz
46.9 kHz
60.0 kHz
68.7 kHz
44.8 kHz
54.8 kHz
64.0 kHz
NO.
1
2
3
4
5
6
7
8
9
10
Page of 42
Display

Click on the first or last page to see other CPD-220AS service manuals if exist.