Read Sony CPD-2001G Service Manual online
SECTION 1
GENERAL
1-1
The operating instructions mentioned here are partial abstracts
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual.
3
Getting Started
J
C
EN
Table of Contents
Installation
•
Prevent internal heat build up by allowing adequate air
circulation. Do not place the monitor on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
circulation. Do not place the monitor on surfaces (rugs,
blankets, etc.) or near materials (curtains, draperies) that
may block the ventilation holes.
•
Do not install the monitor near heat sources such as
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration or shock.
radiators or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration or shock.
•
Do not place the monitor near equipment that generates
magnetism, such as a converter, or high voltage power
lines.
magnetism, such as a converter, or high voltage power
lines.
Maintenance
•
Clean the cabinet, panel and controls with a soft cloth
lightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
lightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
•
Do not rub, touch or tap the surface of the screen with
sharp or abrasive items such as a ball point pen or
screwdriver. This type of contact may scratch the picture
tube.
sharp or abrasive items such as a ball point pen or
screwdriver. This type of contact may scratch the picture
tube.
• Clean the screen with a soft cloth. If you use a glass
cleaning liquid, do not use any type of cleaner containing
an anti-static solution or similar additive as this may
scratch the screen’s coating.
an anti-static solution or similar additive as this may
scratch the screen’s coating.
Transportation
• When you transport this monitor for repair or shipment,
use the original carton and packing material.
Warning on Power Connection
•
Use an appropriate power cord for your local power
supply.
supply.
for 220 to 240 V AC
for 100 to 120 V AC
•
Before disconnecting the power cord, wait for at least 30
seconds after turning off the power to allow the static
electricity on the CRT display surface to discharge.
seconds after turning off the power to allow the static
electricity on the CRT display surface to discharge.
•
After the power has been turned on, the CRT is
demagnetized (degaussed) for about 5 seconds. This
generates a strong magnetic field around the metal frame,
which may affect the data stored on magnetic tapes and
disks near the monitor. Place magnetic recording
equipment, tapes and disks away from this monitor.
demagnetized (degaussed) for about 5 seconds. This
generates a strong magnetic field around the metal frame,
which may affect the data stored on magnetic tapes and
disks near the monitor. Place magnetic recording
equipment, tapes and disks away from this monitor.
Precautions
Examples of plug types:
for 240 V AC only
The socket should be installed near the equipment and
be easily accessible.
be easily accessible.
Precautions ............................................................................... 3
Setup .......................................................................................... 4
Parts and Controls ................................................................... 4
The OSD (On-screen Display) System ................................. 6
Resetting the Adjustments ..................................................... 9
Video Enhancement Mode ................................................... 10
Specifications .......................................................................... 10
Setup .......................................................................................... 4
Parts and Controls ................................................................... 4
The OSD (On-screen Display) System ................................. 6
Resetting the Adjustments ..................................................... 9
Video Enhancement Mode ................................................... 10
Specifications .......................................................................... 10
Monitor Information ............................................................. 10
Power Saving Function and LED Indicator ...................... 11
Plug and Play ......................................................................... 11
Damper wires ......................................................................... 11
Warning Messages ................................................................. 12
Troubleshooting ..................................................................... 12
Power Saving Function and LED Indicator ...................... 11
Plug and Play ......................................................................... 11
Damper wires ......................................................................... 11
Warning Messages ................................................................. 12
Troubleshooting ..................................................................... 12
Getting Started
4
Parts and Controls
Rear
1
(RESET) button (pages 6 and 9)
Resets the adjustments to the factory settings.
2
Video Enhancement Mode button
(page 10)
Selects the Video Enhancement Mode.
3 ¨ (BRIGHTNESS) ./> buttons (page 5)
Adjust the picture brightness.
Operate as the ./> buttons when adjusting other
items.
Operate as the ./> buttons when adjusting other
items.
4
(MENU) button (pages 6 and 10)
Displays the MENU OSD.
5 > (CONTRAST) ?// buttons (page 5)
Adjust the contrast.
Operate as the ?// buttons when adjusting other
items.
Operate as the ?// buttons when adjusting other
items.
6 u (POWER) switch and indicator (page 11)
Turns the monitor on and off.
The indicator lights up green when the monitor is on,
and lights up green and orange when the monitor is in
Power Saving mode.
The indicator lights up green when the monitor is on,
and lights up green and orange when the monitor is in
Power Saving mode.
7 AC IN connector
Provides AC power to the monitor.
8 Video input connector (HD15)
Inputs RGB video signals and SYNC signals
Front
Getting Started
Step 2 Make sure the monitor is switched off and attach the
power cord to the monitor. Then, attach the other end
of the power cord to a power outlet.
of the power cord to a power outlet.
Step 3 Switch on the monitor and computer.
Step 4 Adjust the user controls according to your personal
preference.
Installation is complete.
Installation is complete.
Power cord
to a power outlet
Setup
Connect the monitor to your computer system.
This monitor will sync to platforms running at horizontal frequencies between 30 and 85 kHz.
This monitor will sync to platforms running at horizontal frequencies between 30 and 85 kHz.
Step 1 Make sure the computer system is switched off and
attach the video signal cable to the video output of the
computer.
computer.
to the video output
Computer
to AC IN
Click on the first or last page to see other CPD-2001G service manuals if exist.