Read Sony SLT-A99 / SLT-A99V Service Manual online
SLT-A99/A99V_L2
3-3E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If contamination cannot be removed by the remedy shown above, use the following jig for cleaning.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A)
or cleaning jig (wide) (J-6082-779-A).
If contamination cannot be removed by the remedy shown above, use the following jig for cleaning.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A)
or cleaning jig (wide) (J-6082-779-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to service manual, check if there is dirt on the OLPF.
4. According to service manual, check if there is dirt on the OLPF.
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
cloth in ethyl alcohol.
2
The dry cleaning cloth.
P.O.I.
Claw
OLPF
Mirror Lock Lever
MB Mirror Frame Holder Lock SP
MB Mirror Frame Holder Lock SP
Press the MB Mirror Frame Holder
Lock SP to raise the P.O.I.
Lock SP to raise the P.O.I.
Set the P.O.I. Holder at the
previous position.
previous position.
Unjoint the claw while pressing
the P.O.I. backward.
the P.O.I. backward.
Note: Before starting this work, remove the P.O.I. and set the P.O.I. Holder at the previous position.
Cleaning Jig
(J-6082-635-A)
(J-6082-635-A)
Cleaning Jig (Wide)
(J-6082-779-A)
(J-6082-779-A)
Cleaning Cloth
(J-6082-636-A)
(J-6082-636-A)
Cut
EE3310
