Read Sony SAL50F14Z Service Manual online
2-1
SAL50F14Z (Planar 1,4/50 ZA) (Planar T*50mm F1.4 ZA SSM)
2. DISASSEMBLY
Notches
Holes
How to Use
Attach the chip-A, chip-B or chip-C to the universal wrench.
For the notches:
For the holes:
For the notches:
For the holes:
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc. during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
chip-A, chip-C
chip-B
chip-B
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Chip-C for
universal wrench:
J-6082-609-3
universal wrench:
J-6082-609-3
Notches
Holes
Chip
Chip-A
or
Chip-C
Chip-A
or
Chip-C
Chip-B
Chip-B
Chip
Match the universal wrench to the holes or notches of the lens block, etc.
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
SERVICE TOOLS
B-10
Adhesive bond (B-10): J-6082-612-A
B-40
Adhesive bond (B-40): J-6082-614-A
A-20
Anti-diffusion agent (A-20): J-6082-611-A
Grease (FT-210): 9-913-200-37
FT-210
Grease (G-85): J-6082-626-A
G-85
Grease (G-35): J-6082-621-A
G-35
Grease (G-15): J-6082-619-A
G-15
Grease (O-20): J-6082-610-A
O-20
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
and completely)
NG
(The flexible board was plugged in
crooked.)
crooked.)
NG
(The flexible board was not plugged in
completely.)
completely.)
Flexible
Board
Flexible
Board
Board
Connector
Connector
Reference line
Flexible
Board
Board
Connector
Connector
Flexible
Board
Reference line
Connector
Connector
Flexible
Board
Board
Flexible
Board
Reference line
Fig. 1
Fig. 2
Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
a flexible board in direction B.
Holder
Connector
Flexible Board
A
A
Holder
Insulation side
Connector
Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
broken.
Click on the first or last page to see other SAL50F14Z service manuals if exist.