Read Sony ILCE-7S (serv.man2) Service Manual online
ILCE-7S_L2
2-7
2-1-5. IMAGER BLOCK SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
Note
201
4-537-661-01
SHEET DP, N FRAME (785)
202
4-537-719-02
SHEET, IM CONDUCTION (3200) (Note 5)
* 203
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
204
4-480-795-02
BUTTON, LENS LOCK (779)
205
A-2058-108-A SERVICE (3200), DEVICE (Note 4)
206
1-490-193-21
SHUTTER UNIT (AFE-3313)
207
A-1902-075-C MB CHARGE UNIT (456)
208
1-886-243-11
ISP-008 FLEXIBLE BOARD
209
1-893-037-11
IS-1014 FLEXIBLE BOARD
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#238 4-287-436-01 SCREW
(M1.7)
#267
4-287-436-21
SCREW (M1.7) (Note 1)
DISASSEMBLY
1. Remove in numerical order (
1
to
4
) in the left figure.
1
#267 X 3
#267
Back View
3
#238 X 3
#238
Back View
4
#197 X 1
#197
Front View
Note 1: Refer to “Assembly-1: Screw tightening sequence when
assembling the IM heatsink (3200)”.
Note 1: “Assembly-1: Screw tightening sequence when assembling
the IM heatsink (3200) ” を参照してください。
Note 2: The IM adjust washers (C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
nal places.
When replacing IM adjust washers, refer to “SELECTION
PARTS” If the original state cannot be restored due to loss
of the IM adjust washer, for example, replace the Device
Service (3200).
PARTS” If the original state cannot be restored due to loss
of the IM adjust washer, for example, replace the Device
Service (3200).
Note 3: Refer to “Assembly-2: IM Adjust Washer (C) putting posi-
tion” when you assemble.
Note 2: IM調整ワッシャ (C) は,それぞれ厚さが異なります。取り
外したIM調整ワッシャは,必ず元の位置に戻してください。
ま た,IM調 整 ワ ッ シ ャ を 交 換 す る 際 は,“SELECTION
PARTS”を参照してください。IM adjust washerを紛失する
などして元の状態に戻せなくなった場合は,Device Service
などして元の状態に戻せなくなった場合は,Device Service
(3200) を交換してください。
Note 3: 組立時は“Assembly-2: IM Adjust Washer (C) putting position”
を参照してください。
Note 4: Precautions for Replacement of the Front Block Assy
Service
As Front Block Assy Service may be damaged by static elec-
tricity from its structure, handle it carefully like for the MOS IC.
tricity from its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
nor exposed to strong light.
Note 4: フロントブロックAssy サービス交換時の注意
フロントブロックAssy サービスは構造上,静電気により破壊
される恐れがあるため,MOS ICと同様に注意して取り扱って
される恐れがあるため,MOS ICと同様に注意して取り扱って
ください。
また,受光部にはゴミの付着,および強い光がはいることの
ないように注意してください。
#267
(Note 1)
(Note 1)
#267
(Note 1)
(Note 1)
#238
#197
1
Imager Unit Section
(See page 2-8)
205
208
4
207
3
206
209
203
(Note 2, 3)
203
(Note 2, 3)
202
202
203
(Note 2, 3)
204
201
Mount Section
(See page 2-9)
(including IC6101 (CMOS imager)
and IS-1012 complete board)
(Note 4)
and IS-1012 complete board)
(Note 4)
2
ns
ns
(Note 5)
(Note 5)
Screw
#197: M1.6 X 4.5 (Tapping)
(Silver)
4-185-990-01
4-185-990-01
4.5
1.6
#238:
M1.7 X 3.5
(Black)
4-287-436-01
(Black)
4-287-436-01
3.5
1.7
5.0
1.7
#267: M1.7 X 5.0
(Red)
4-287-436-21
4-287-436-21
SELECTION PARTS
Ref. No.203
Select the optimum thickness of washer.
Part No.
Description
* 4-185-999-01 IM WASHER (C), ADJUST (t = 0.05)
* 4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
* 4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
* 4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
* 4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
* 4-185-999-11 IM WASHER (C), ADJUST (t = 0.1)
* 4-185-999-21 IM WASHER (C), ADJUST (t = 0.15)
* 4-185-999-31 IM WASHER (C), ADJUST (t = 0.2)
* 4-185-999-41 IM WASHER (C), ADJUST (t = 0.25)
Part No.
Description
* 4-185-999-51 IM WASHER (C), ADJUST (t = 0.3)
* 4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
* 4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
* 4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
* 4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
* 4-185-999-61 IM WASHER (C), ADJUST (t = 0.35)
* 4-185-999-71 IM WASHER (C), ADJUST (t = 0.4)
* 4-185-999-81 IM WASHER (C), ADJUST (t = 0.45)
* 4-185-999-91 IM WASHER (C), ADJUST (t = 0.495)
Note 5: Do not reuse these Parts because their adhesive force de-
creases when they are removed once.
Note 5: これらの部品は一度剥がすと粘着力が弱くなるため、再利用
はしないでください。
Click on the first or last page to see other ILCE-7S (serv.man2) service manuals if exist.