Read Sony ILCE-3000K / ILCE-3500J (serv.man2) Service Manual online
ILCE-3000K/3500J_L2
– 2 –
SPECIFICATIONS
Camera
[System]
Camera type: Interchangeable lens
digital
digital
camera
Lens: E-mount lens
[Image sensor]
Image sensor: APS-C format
(23.2 mm × 15.4 mm) CMOS
image
sensor
Total pixel number of image sensor:
Approx. 20 400 000 pixels
Effective pixel number of camera:
Approx. 20 100 000 pixels
[Auto focus system]
System: Contrast detection system
Sensitivity range: EV0 to EV20 (at ISO
Sensitivity range: EV0 to EV20 (at ISO
100 conversion, with F2.8 lens)
[Exposure control]
Metering method: 1 200-segment
metering by the image sensor
Metering range: EV0 to EV20 (at ISO
100 conversion, with F2.8 lens)
ISO sensitivity (Recommended
exposure
exposure
index):
Still images: AUTO, ISO 100 –
ISO
16000
Movies: AUTO, ISO 100 –
ISO 3200 equivalent
Exposure compensation:
±3.0 EV (1/3 EV step)
[Shutter]
Type: Electronically-controlled,
vertical-traverse, focal-plane type
Speed range:
Still images: 1/4 000 second to
30 seconds, BULB
Movies: 1/4 000 second to
1/4 second (1/3 EV step),
1080 60i-compatible device up to
1/30 second in AUTO mode
1080 50i-compatible device up to
1/25 second in AUTO mode
Flash sync speed: 1/160 second
[Recording media]
“Memory Stick XC Duo” media,
“Memory Stick PRO Duo” media,
SD
card
[Electronic viewfinder]
Type: Electronic viewfinder
Screen size: 0.5 cm (0.20 type)
Total number of dots:
Screen size: 0.5 cm (0.20 type)
Total number of dots:
201 600 dots equivalent
Frame coverage: 100%
Magnification: 0.70 × with 50 mm lens
Magnification: 0.70 × with 50 mm lens
at infinity, –1 m
–1
(diopter)
Eye point: Approx. 21 mm from the
eyepiece, 15 mm from the eyepiece
frame at –1 m
–1
(diopter)
Diopter adjustment:
–4.0
–4.0
m
–1
to +3.5 m
–1
(diopter)
[LCD screen]
LCD panel: Wide, 7.5 cm (3.0 type)
TFT
TFT
drive
Total number of dots: 230 400 dots
[Input/output terminals]
Multi/Micro USB Terminal*:
USB
USB
communication
* Supports Micro USB compatible device.
[Power]
Battery type: Rechargeable battery
pack
pack
NP-FW50
[Power consumption]
When using an E 18-55 mm F3.5-5.6
OSS
OSS
lens
When using the viewfinder:
Approx.
2.0
W
When using an LCD screen:
Approx.
1.9
W
[Others]
Exif Print: Compatible
PRINT Image Matching III:
Compatible
DPOF: Compatible
Dimensions (CIPA compliant)
(Approx.):
PRINT Image Matching III:
Compatible
DPOF: Compatible
Dimensions (CIPA compliant)
(Approx.):
128.0 mm × 90.9 mm × 84.5 mm
(5 1/8 inches × 3 5/8 inches ×
3 3/8 inches) (W/H/D)
Mass (CIPA compliant) (Approx.):
411 g (14.5 oz) (including battery
and “Memory Stick PRO Duo”
media)
353 g (12.5 oz) (camera only)
Operating temperature: 0 °C to 40 °C
(32 °F to 104 °F)
File format:
Still image: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
compliant, RAW (Sony ARW
2.3
Format)
Movie (AVCHD format): AVCHD
format Ver. 2.0 compatible
Video:
MPEG-4
AVC/H.264
Audio: Dolby Digital 2ch
Dolby Digital Stereo Creator
• Manufactured under license from Dolby
Laboratories.
Movie (MP4 format):
Video:
MPEG-4
AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
USB communication:
Hi-Speed USB (USB 2.0)
[Flash]
Flash guide number:
4 (in meters at ISO 100)
Recycling time: Approx. 4 seconds
Flash coverage: Covering 16 mm lens
Flash coverage: Covering 16 mm lens
(focal length that the lens indicates)
Flash compensation:
±2.0 EV (1/3 EV step)
Rechargeable battery pack
NP-FW50
NP-FW50
Battery type: Lithium-ion battery
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
Minimum 7.3 Wh (1 020 mAh)
Maximum dimensions (Approx.):
31.8 mm × 18.5 mm × 45 mm
(1 5/16 inches × 3/4 inches ×
1 13/16 inches) (W/H/D)
Mass (Approx.): 57 g (2.1 oz)
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE WITH
MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
Their evaporation caused by improper management affects your health
and environment, and wastes resources.
Manage the chemicals carefully as follows.
•
Store chemicals sealed in a specific place to prevent from exposure
to high temperature or direct sunlight.
to high temperature or direct sunlight.
•
Avoid dividing chemicals into excessive numbers of small containers
to reduce natural evaporation.
to reduce natural evaporation.
•
Keep containers sealed to avoid natural evaporation when chemicals
are not in use.
are not in use.
•
Avoid using chemicals as much as possible. When using chemicals,
divide only required amount to a small plate from the container and
use up it.
divide only required amount to a small plate from the container and
use up it.
EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
•
Use a piece of cleaning paper or cleaning cloth for cleaning plastic
parts. Avoid using chemicals.
parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint
thinner, ketone, nor alcohol.
thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a
plastic part.
Be careful not to tighten screws too much.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 350°C during
repairing.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•
Set the soldering iron tip temperature to 350°C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
•
Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenom-
enon.
those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenom-
enon.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
Model information table
Model
ILCE-3000K
ILCE-3500J
Destination
US, CND, E, KR, BR
AEP, UK, RU, E, AUS, CH, JE
US, CND, E, BR
RU, E
, IND
, AUS
Color system
NTSC
PAL
NTSC
PAL
Lens
E 18-55 mm F3.5-5.6 OSS
E 18-55 mm F3.5-5.6 OSS
E 18-50 mm F4-5.6
E 18-50 mm F4-5.6
• Abbreviation
AUS
AUS
:
Australian
model
BR :
Brazilian
model
CH :
Chinese
model
CND
:
Canadian
model
IND :
Indian
model
JE :
Tourist
model
KR :
Korea
model
RU :
Russian
model
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Ver. 1.3 2015.07
Click on the first or last page to see other ILCE-3000K / ILCE-3500J (serv.man2) service manuals if exist.