Read Sony DSLR-A500 / DSLR-A550 Service Manual online
DSLR-A500/A550_L2
2-9
2-1-7. ANTI SHAKE UNIT SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
301
A-1741-366-A SLIDER UNIT (857 SERVICE)
(including HOL-006 flexible board)
302
2-688-377-01
PLATE, LOW PASS RETAINER
303
3-273-746-01
SHEET, LOWPASS FILTER MASK
304
A-1736-386-A ASM UNIT (857) (including IC4001 (CMOS imager)
and IS-071 complete board) (A500) (Note 1, 2, 3)
304
A-1736-424-A UNIT, OMEGA (858) (including IC4205
(CMOS imager) and IS-060 complete board)
(A550) (Note 1, 2, 3)
305
1-788-639-11
OPTICAL FILTER BLOCK (OFB-01-04) (Note 3)
306
4-155-209-01
SHEET SPACER (A500) (Note 3)
306
A-1736-609-A PLATE ASSY, SPACER (858) (A550) (Note 3)
307
1-880-440-11
IS-049 FLEXIBLE BOARD (A550)
307
1-880-441-11
IS-050 FLEXIBLE BOARD (A500)
308
1-880-442-11
IS-051 FLEXIBLE BOARD
309
3-268-998-01
PLATE FPC GUIDE (A550)
* 309
4-155-210-01
PLATE FPC GUIDE (A500)
#64
2-666-551-21
SCREW, TAPPING, P2 (Silver)
Screw
IDENTIFYING PARTS
ASSEMBLY
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
(Silver)
2-666-551-21
5.0
1.7
ns
ns
#64
#64
301
(including HOL-006 flexible board)
302
303
305
(Note 3)
306
(Note 3)
307
304
(including IC4001 (A500)/IC4205 (A550) (CMOS imager) and
IS-060 (A550)/IS-071 (A500) complete board)
(Note 1, 2, 3)
IS-060 (A550)/IS-071 (A500) complete board)
(Note 1, 2, 3)
308
309
Note
Note 2: Refer to “3-3. CLEANING PROCEDURE OF OLPF” on
page 3-7 for method of cleaning the OLPF.
Note 2:
OLPFの 清 掃 方 法 は3-7ペ ー ジ の 3-3. CLEANING
PROCEDURE OF OLPF を参照してください。
Note 1:
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from its
structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with dusts
nor exposed to strong light.
Note 1:
イメージャ交換時の注意
イメージャ交換時の注意
・ イメージャを交換した場合は,カメラ部の全調整を行って
ください。
・ イメージャは構造上,静電気により破壊される恐れがある
ため,MOS ICと同様に注意して取り扱ってください。
また,受光部にはゴミの付着,および強い光がはいること
のないように注意してください。
Note 3: Refer to below when replacing the optical filter block.
Disassembly
1. Pour the solvent (alcohol or cleaning liquid) between
1. Pour the solvent (alcohol or cleaning liquid) between
the imager and the spacer.
∗ Wait for the adhesive power of the adhesive tape to
weaken.
2. Remove the spacer from the imager.
Assembly
1. Paste the optical filter block so that an upper, lower,
1. Paste the optical filter block so that an upper, lower,
right and left may become uniform for the spacer.
∗ Replace the new one without reusing the spacer.
∗ Refer to the figure below for the direction that the
optical filter block installs.
2. Paste the spacer so that an upper, lower, right and
left may become uniform for the imager.
Pour the solvent
(alcohol or cleaning liquid).
(alcohol or cleaning liquid).
Optical Filter Block
Spacer
Imager
Imager
Imager
Side
Side
Mount
Side
Side
Optical Filter Block
Spacer
Peel off eleased paper.
Peel off eleased paper.
Two layers are
imager side.
imager side.
Note 3:
光学フィルタブロックを交換する際は下記を参照してく
ださい。
外し方
1. イメージャとスペーサの間に溶剤(アルコール又は
クリーニング液)を流し込む。
∗ 両面テープの粘着力が弱くなるのを待ってください。
2. イメージャからスペーサを取り外す。
1. イメージャとスペーサの間に溶剤(アルコール又は
クリーニング液)を流し込む。
∗ 両面テープの粘着力が弱くなるのを待ってください。
2. イメージャからスペーサを取り外す。
溶剤(アルコール又は
クリーニング液)を流し込む。
クリーニング液)を流し込む。
取り付け方
1. スペーサに対し,上下左右が均一になるように光学フィルタ
ブロックを貼り付ける。
∗ スペーサは再利用せずに新しいものと交換してください。
∗ 光学フィルタブロックの取り付け方向は下図を参照して
ください。
2. イメージャに対し,上下左右が均一になるようにスペーサを
貼り付ける。
1. スペーサに対し,上下左右が均一になるように光学フィルタ
ブロックを貼り付ける。
∗ スペーサは再利用せずに新しいものと交換してください。
∗ 光学フィルタブロックの取り付け方向は下図を参照して
ください。
2. イメージャに対し,上下左右が均一になるようにスペーサを
貼り付ける。
光学フィルタブロック
スペーサ
イメージャ
イメージャ
光学フィルタブロック
スペーサ
剥離紙を剥がす。
2層側が
イメージャ側
イメージャ側
イメージャ
側
側
マウント
側
側
剥離紙を剥がす。
Click on the first or last page to see other DSLR-A500 / DSLR-A550 service manuals if exist.