MEX-DV900, MEX-DV90EE - Sony Car Audio Service Manual (repair manual). Page 9

Read Sony MEX-DV900 / MEX-DV90EE Service Manual online

MEX-DV90EE/DV900
9
(DV900: E and Indian models)
A
B
VIDEO OUT
Monitor*
Monitor*
ⲥ㾚఼
*
REAR AUDIO OUT
VIDEO OUT
Monitor*
Monitor*
ⲥ㾚఼
*
* not supplied 
no suministrado
 䴲䰘䗕
* not supplied 
no suministrado
 䴲䰘䗕
Connection diagram
 To a metal surface of the car
First connect the black ground (earth) lead, then connect the 
yellow and red power supply leads.
 To the power antenna (aerial) control lead or 
power supply lead of antenna (aerial) booster 
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a 
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in the 
rear/side glass, see “Notes on the control and power supply 
leads.”
 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other 
system may damage the unit.
 To the +12 V power terminal which is 
energized in the accessory position of the 
ignition switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal 
surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in the 
rear/side glass, see “Notes on the control and power supply 
leads.”
 To the +12 V power terminal which is 
energized at all times
Be sure to connect the black ground (earth) lead to a metal 
surface of the car first.
 To the parking brake switch cord
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the 
rear/side glass, connect the power antenna (aerial) control lead 
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used 
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will 
always be supplied to the memory circuit even when the ignition 
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with 
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or 
connect the terminals of the right speakers with those of the left 
speaker.
• Do not connect the ground (earth) lead of this unit to the 
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage 
the unit.
• To avoid a malfunction, do not use the built-in speaker leads 
installed in your car if the unit shares a common negative (–) 
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Notes on connection
• If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and 
amplifier are connected correctly.
• If you are to use the monitor for the rear seats, connect the 
parking brake switch cord to the ground (earth).
Cautions
• This unit is designed for negative ground (earth) 12 V
DC operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to 
avoid short circuits.
• Connect the yellow and red power supply leads only 
after all other leads have been connected.
• Run all ground (earth) leads to a common 
ground (earth) point.
• Be sure to insulate any loose unconnected leads with 
electrical tape for safety.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other 
stereo components, the connected car circuit’s rating 
must be higher than the sum of each component’s fuse.
• When no car circuits are rated high enough, connect 
the unit directly to the battery.
Connection example
Notes (
-B)
• Be sure to connect the ground (earth) lead before connecting 
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
L
R
AUX
IN
VIDEO
OUT
AUX IN
REAR AUDIO OUT
VIDEO OUT
from car antenna (aerial)
desde la antena del automóvil
ᴹ㞾≑䔺໽㒓
AMP REM
Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
᳔໻⬉⌕$
Fuse (10 A)
Fusible (10 A)
ֱ䰽ϱ$
Blue/white striped
Con rayas azules y blancas
㪱㡆ˋⱑ㡆ᴵ㒍
Red
Rojo
㑶㡆
Yellow
Amarillo
咘㡆
White
Blanco
ⱑ㡆
Green
Verde
㓓㡆
Purple
Morado
㋿㡆
White/black striped
Con rayas blancas y negras
ⱑ㡆ˋ咥㡆ᴵ㒍
Gray/black striped
Con rayas grises y negras
♄㡆ˋ咥㡆ᴵ㒍
Green/black striped
Con rayas verdes y negras
㓓㡆ˋ咥㡆ᴵ㒍
Gray
Gris
♄㡆
Left
Izquierdo
Ꮊ
Right
Derecho
ে
Left
Izquierdo
Ꮊ
Right
Derecho
ে
ANT REM
Black
Negro
咥㡆
Blue
Azul
㪱㡆
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
᳔໻⬉⌕ $
Purple/black striped
Con rayas moradas y negras
㋿㡆ˋ咥㡆ᴵ㒍
*
1
*
2
Monitor (not supplied)
Monitor (no suministrado)
ⲥ㾚఼䴲䰘䗕
Light green
Verde claro
⎵㓓㡆
*
1
RCA pin cord (not supplied)
*
2
For details on connecting to the parking
brake switch cord, see “Connecting the 
parking brake cord (
)” on the reverse
side.
*
3
Auxiliary device such as hideaway
navigation device, TV tuner box, etc.
*
1
Cable con terminales RCA 
(no suministrado)
*
2
Para obtener detalles acerca de cómo 
conectar el cable de conmutación del 
freno de estacionamiento, consulte 
“Conexión del cable del freno de 
estacionamiento (
)” en el dorso.
*
3
Dispositivo auxiliar como, por 
ejemplo, un dispositivo de navegación
independiente, un sintonizador de 
televisión, etc.
*
1
5&$䩜ᇐ㒓˄䴲䰘䗕˅
*
2
᳝݇䖲᥹㟇ذ䔺ࠊࡼᓔ݇ᇐ㒓ⱘ䆺㒚䇈
ᯢˈ䇋খ䯙ড䴶ⱘĀ䖲᥹ذ䔺ࠊࡼ⬉㒓
˄
˅āDŽ
*
3
՟བ䱤㮣ᓣᇐ㟾䆒໛ǃ79䇗䇤Ⲧㄝ䕙ࡽ
䆒໛DŽ
PARKING BRAKE
*
3
Ver. 1.1
Page of 76
Display

Click on the first or last page to see other MEX-DV900 / MEX-DV90EE service manuals if exist.

Random: