Read Sony MDX-F5800 Service Manual online
8
MDX-F5800
2
A
B
AUDIO OUT REAR
AUDIO OUT FRONT
BUS AUDIO IN
BUS CONTROL IN
BUS CONTROL IN
BUS AUDIO IN
Source selector *
XA-C30
* not supplied
(AEP, UK models)
L
R
5
7
4
8
1
3
5
7
2
4
6
8
A
B
AMP REM
ATT
AUDIO OUT
REAR
*
3
BUS
CONTROL IN
AUDIO OUT
FRONT
BUS AUDIO IN
REMOTE
IN
Source selector
(not supplied)
(not supplied)
XA-C30
Supplied with the MD/CD changer
*
2
5
from car aerial
*
1
Fuse (10 A)
7
Light blue
Blue/white striped
*
4
Max. supply current 0.3 A
Yellow
Blue
continuous power supply
power aerial control
7
8
4
5
Red
Black
switched power supply
earth
Positions 1, 2, 3 and 6 do not have pins.
1
2
3
4
Speaker, Rear, Right
Speaker, Rear, Right
Speaker, Front, Right
Speaker, Front, Right
5
6
7
8
Speaker, Front, Left
Speaker, Front, Left
Speaker, Rear, Left
Speaker, Rear, Left
Purple
White
Grey
+
–
+
–
+
–
+
–
from the car’s speaker connector
from the car’s power connector
See “Power connection diagram” on the reverse side for details.
3
Negative polarity positions 2, 4, 6, and 8 have striped leads.
Green
Supplied with XA-C30
*
2
*
1
Note for the aerial connecting
If your car aerial is an ISO (International
Organisation for Standardisation) type, use the
supplied adaptor 5 to connect it.
First connect the car aerial to the supplied
adaptor, then connect it to the aerial jack of the
master unit.
If your car aerial is an ISO (International
Organisation for Standardisation) type, use the
supplied adaptor 5 to connect it.
First connect the car aerial to the supplied
adaptor, then connect it to the aerial jack of the
master unit.
*
2
RCA pin cord (not supplied)
*
3
AUDIO OUT can be switched REAR or SUB.
For details, see the Operating Instructions
manual.
For details, see the Operating Instructions
manual.
*
4
Insert with the cord downwards
Connection example (
2
)
Notes (2-A)
• Be sure to connect the earth lead before connecting the amplifier.
• If you connect an optional power amplifier and do not use the
• Be sure to connect the earth lead before connecting the amplifier.
• If you connect an optional power amplifier and do not use the
built-in amplifier, the beep sound will be deactivated.
Tip (2-B-
)
For connecting two or more MD/CD changers, the source selector XA-
C30 (optional) is necessary.
C30 (optional) is necessary.
Connection diagram (
3
)
A
To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting any other
system may damage the unit.
This connection is only for amplifiers. Connecting any other
system may damage the unit.
B
To the interface cable of a car telephone
Warning
If you have a power aerial without a relay box, connecting this unit
with the supplied power connecting lead 7 may damage the aerial.
with the supplied power connecting lead 7 may damage the aerial.
Notes on the control leads
• The power aerial control lead (blue) supplies +12 V DC when you
• The power aerial control lead (blue) supplies +12 V DC when you
turn on the tuner, or when you activate the AF (Alternative
Frequency) or TA (Traffic Announcement) function.
Frequency) or TA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW aerial in the rear/side glass,
connect the power aerial control lead (blue) or the accessory power
input lead (red) to the power terminal of the existing aerial
booster. For details, consult your dealer.
input lead (red) to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without a relay box cannot be used with this unit.
Memory hold connection
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
When the yellow power input lead is connected, power will always
be supplied to the memory circuit even when the ignition switch is
turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or connect
the terminals of the right speakers with those of the left speaker.
• Do not connect the earth lead of this unit to the negative (–)
terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers (with
• Connect only passive speakers. Connecting active speakers (with
built-in amplifiers) to the speaker terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–) lead
for the right and left speakers.
for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Click on the first or last page to see other MDX-F5800 service manuals if exist.