Read Sony CDX-GT33U Service Manual online
SERVICE MANUAL
Sony Corporation
Audio&Video Business Group
Published by Sony Techno Create Corporation
CDX-GT33U
AEP, UK, Italian, Russian model
FM/MW/LW COMPACT DISC PLAYER
E, Mexican model
FM/AM COMPACT DISC PLAYER
9-889-450-01
2009C04-1
©
2009.03
AEP Model
UK Model
E Model
Ver. 1.0 2009.03
SPECIFICATIONS
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
Frequency response: 10 – 20,000 Hz
Wow and fl utter: Below measurable limit
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz (AEP, UK, IT, RU model)
87.5 – 107.9 MHz (E, MX model)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
Tuning range:
87.5 – 108.0 MHz (AEP, UK, IT, RU model)
87.5 – 107.9 MHz (E, MX model)
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 150 kHz
Usable sensitivity: 10 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 70 dB (mono)
Separation: 40 dB at 1 kHz
Frequency response: 20 – 15,000 Hz
AM (E, MX model)
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26
Tuning range: 530 – 1,710 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: 26
μV
MW/LW (AEP, UK, IT, RU model)
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: MW: 26
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal:
External antenna (aerial) connector
Intermediate frequency: 25 kHz
Sensitivity: MW: 26
μV, LW: 45 μV
Photo: E model
Model Name Using Similar Mechanism
CDX-GT430U/GT434U
CD Drive Mechanism Type
MG-101Y-188//Q
Optical Pick-up Name
DAX-25A
USB Player section
Interface: USB (Full-speed)
Maximum current: 500mA
Maximum current: 500mA
Power amplifi er section
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 45 W × 4 (at 4 ohms)
Speaker impedance: 4 – 8 ohms
Maximum power output: 45 W × 4 (at 4 ohms)
• The tuner and CD sections have no adjustments.
– Continued on next page –
CDX-GT33U
2
General
Output:
Power antenna (aerial) relay control terminal
Inputs:
Telephone ATT control terminal
(AEP, UK, IT, RU model)
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 × 50 × 179 mm
(7
Power antenna (aerial) relay control terminal
Inputs:
Telephone ATT control terminal
(AEP, UK, IT, RU model)
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative ground (earth))
Dimensions: Approx. 178 × 50 × 179 mm
(7
1
/
8
× 2 × 7
1
/
8
in.) (w/h/d)
Mounting dimensions: Approx. 182 × 53 × 162 mm
(7
(7
1
/
4
× 2
1
/
8
× 6
1
/
2
in.) (w/h/d)
Mass: Approx. 1.2 kg (2 lb. 11 oz.)
Supplied accessories:
Card remote commander: RM-X151 (E, MX model)
Parts for installation and connections (1 set)
Supplied accessories:
Card remote commander: RM-X151 (E, MX model)
Parts for installation and connections (1 set)
Design and specifi cations are subject to change without notice.
• Abbreviation
IT
IT
: Italian model
RU
: Russian model
MX
: Mexican model
SAFETY-RELATED COMPONET WARNING!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
NOTES ON CHIP COMPONENT REPLACEMENT
•
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
aged by heat.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
Use of controls or adjustments or performance of procedures
other than those specifi ed herein may result in hazardous radia-
tion exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostat-
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
ic break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
TEST DISCS
Please use the following test discs for the check on the CD section.
Please use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical
pick-up block.
optical pick-up block.
Never turn the semi-fi xed resistor located at the side of optical
pick-up block.
optical pick-up
semi-fixed resistor
CDX-GT33U
3
1.
SERVICE NOTE
..................................................... 4
2. GENERAL
Location of Controls ....................................................... 5
Connections
....................................................................
7
3. DISASSEMBLY
3-1. Sub Panel Assy ............................................................... 11
3-2. CD Mechanism Block ..................................................... 11
3-3. MAIN Board ................................................................... 12
3-4. SERVO
3-2. CD Mechanism Block ..................................................... 11
3-3. MAIN Board ................................................................... 12
3-4. SERVO
Board
................................................................. 12
3-5. Chassis (T) Sub Assy ...................................................... 13
3-6. Roller Arm Assy .............................................................. 13
3-7. Chassis
3-6. Roller Arm Assy .............................................................. 13
3-7. Chassis
(OP)
Assy
........................................................... 14
3-8. Chucking Arm Sub Assy ................................................. 14
3-9. Sled
3-9. Sled
Motor
Assy
.............................................................. 15
3-10. Optical Pick-up Section .................................................. 16
3-11. Optical Pick-up ............................................................... 16
3-11. Optical Pick-up ............................................................... 16
4. DIAGRAMS
4-1. Block Diagram –Main Section– ..................................... 17
4-2. Block Diagram –Display Section– ................................. 18
4-3. Printed Wiring Board –Main Section– ............................ 20
4-4. Schematic Diagram –Main Section (1/3)– ...................... 21
4-5. Schematic Diagram –Main Section (2/3)– ...................... 22
4-6. Schematic Diagram –Main Section (3/3)– ...................... 23
4-7. Printed Wiring Boards –Key Section– ............................ 24
4-8. Schematic Diagram –Key Section– ................................ 25
4-2. Block Diagram –Display Section– ................................. 18
4-3. Printed Wiring Board –Main Section– ............................ 20
4-4. Schematic Diagram –Main Section (1/3)– ...................... 21
4-5. Schematic Diagram –Main Section (2/3)– ...................... 22
4-6. Schematic Diagram –Main Section (3/3)– ...................... 23
4-7. Printed Wiring Boards –Key Section– ............................ 24
4-8. Schematic Diagram –Key Section– ................................ 25
5.
EXPLODED VIEWS
5-1. Main
Section
................................................................... 30
5-2. Front Panel Section ......................................................... 31
5-3. CD Mechanism Section (MG-101Y-188//Q) .................. 32
5-3. CD Mechanism Section (MG-101Y-188//Q) .................. 32
6.
ELECTRICAL PARTS LIST
.............................. 33
TABLE OF CONTENTS
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
This compact disc player is classifi ed as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
exterior.
This label is located on the bottom of the chassis.
• CD playback
You can play CD-DA (also containing CD TEXT), CD-R/CD-
RW (MP3/WMA/AAC fi les).
RW (MP3/WMA/AAC fi les).
Type of discs
Label on the disc
CD-DA
MP3
WMA
AAC
CDX-GT33U
4
SECTION 1
SERVICE NOTE
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
When repairing or servicing this set, connect the jig (extension
cable) as shown below.
• Connect the MAIN board (CN701) and the SERVO board
(CN401) with the extension cable (Part No. J-2502-076-1).
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (Part No. A-1555-
002-A) should be replaced since any parts in the SERVO board
cannot be repaired.
When repairing, the complete SERVO board (Part No. A-1555-
002-A) should be replaced since any parts in the SERVO board
cannot be repaired.
NOTE FOR REPLACEMENT OF THE USB CONNECTOR
(CN902)
To replace the USB connector requires alignment.
1. Insert the USB connector into the front panel.
2. Place the KEY board on the front panel and align the terminals
(CN902)
To replace the USB connector requires alignment.
1. Insert the USB connector into the front panel.
2. Place the KEY board on the front panel and align the terminals
of the USB connector with the holes in the KEY board.
3. Solder the four terminals of the connector.
NOTE FOR THE 20-PIN CONNECTOR (CN901)
Do not use alcohol to clean the 20-pin connector (CN901) connect-
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.
Do not use alcohol to clean the 20-pin connector (CN901) connect-
ing the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor con-
tact may be caused.
SERVO BOARD
CN401
CN401
MAIN BOARD
CN701
CN701
J-2502-076-1
KEY board
front panel
USB (socket) connector