AR-651 (serv.man48). ROM upgrade ... (5) - Sharp Copying Equipment Technical Bulletin (repair manual)

ar-651 (serv.man48) technical bulletin
Model
AR-651 (serv.man48)
Pages
10
Size
153.94 KB
Type
PDF
Document
Technical Bulletin
Brand
Device
Copying Equipment / ROM upgrade ... (5)
File
ar-651-sm48.pdf
Date

Read Sharp AR-651 (serv.man48) Technical Bulletin online

AR568
Sharp Electronics (UK) Ltd., Technical Services Group
1. Model Name
AR-651/810
2.Description
ROM Upgrade (5)
System ROM, UI-ROM, Laser ROM and PFC-ROM have been upgraded.
From October 2003 production
ROM
System ROM
UI ROM
Main ROM
Laser ROM
Scanner ROM
PFC
ROM
RADF
ROM
Version
010
010
010
13
09
08
08
03
Corrected problems
1. When upgrading SYS-ROM at Ver.008 or below to Ver.009 without formatting HDD, F10
error occurred. It has been corrected.
2. E-Mail setting was disabled in German mode with AR-P15 installed, which has been corrected.
3. With following conditions, if the laser beam location control is started while the polygon
motor is rotating through inertia, “Image failure” or “Service Call CA9” may occur on very
rare occasions. This has been corrected not to occur.
1) Open-Close door quickly in the ready condition.
2) Just after starting pre-heat, cancel pre-heating.
4. Regarding [Correction for the missing image 1/3 from the rear end] described in T/R No.ARE-548R,
the control has been corrected not to generate discontinuity of signal occurred in the line
counter signal of PLG PWB and SYS PWB.
5. The failure that interrupts the cassette raising if the paper feeding cover (or Bypass unit
cover) is opened while the cassette tray is raising, which has been corrected.
Specification change
1. “7mm fixed” stitch margin can be changed by addition of 08 code (306,307).
2. For using a double-sided original, Double count display function has been added.
3. Checking of the sensor detection for the vibration caused by closing Tandem LCF has been
abolished.  However, the sensor detection is checked for the condition with gate open as
ever.
Note) 1. Be sure that the corrected version is the above combination of versions or above.
2. Never use the combination other than this combination of ROM versions. Since the
operation checks for other combinations were not performed, the failure such as
malfunction may occur.
ROM UPGRADE ..... (5)
TECHNICAL BULLETIN
Date:
19 April 2004
Model: AR651 
810
Ref.:
012
Colour: White
Page:
1 of 10
AR568
Sharp Electronics (UK) Ltd., Technical Services Group
Addition and Change in [Service Handbook]. (For this upgrading.)
1. Change of Setting mode (08).
Setting mode (08)
Code
Setting item
Default
Tolerance
Content
Before
0
0,2
0:Not display 2:Displayed
332
Original counter
display
After
0
0,2,4
0:Not display 2:Displayed
4:Double counted for double-
sided original
2. Addition to Setting mode (08)
Setting mode (08)
Code
Setting item
Target
function
Default
Tolerance
Content
Operatio
n
procedur
e
306
Stitch margin
default setting
(Left or Right
stitch)
PPC
Front
stitch:0
Back
stitch:0
Front: 0~40
Back: -40~40
Front stitch
0:7mm 1:1mm 2:2mm...
7:7mm....   40:40mm
Back stitch
- 40:- 40mm -39:-39mm...
0:7mm....   40:40mm
4
307
Stitch margin
default setting
(Center stitch)
PPC
0
0,2~30
0:7mm 2:2mm 3:3mm...
7:7mm....   30:30mm
1
3.Parts Name
Current parts
New parts
Ref.
No.
Model
name
Version P/G No.
Parts code
Parts code
Price
rank
Parts name
Effective
time
Inter-
change
-
ability
Note
1
201-15
0N6LA07749500
0N6LA07749600
SYSTEM ROM
010R1
2
201-16
0N6LA07751500
0N6LA07751600
SYSTEM ROM
010R2
3
201-17
0N6LA07752500
0N6LA07752600
BW
UI ROM 010
4
201-13
0N6LA07739500
0N6LA07739600
LASER ROM 09
5
AR-651
AR-810
ALL
201-14
0N6LA07740400
0N6LA07740500
BR
PFC ROM 08
2003/10
3
<Interchange>
1. Interchangeable.
4. Not interchangeable.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
5. Interchangeable if replaced with same types of
related parts in use.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
6. Others.
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
AR568
Sharp Electronics (UK) Ltd., Technical Services Group
ROM Upgrading (4)
After upgrading System ROM, perform "08-690"to initialize the HDD.
If the HDD is not initialized, F10 error will occur.
1) By initializing the HDD, the following information will be erased.
Stored data by "Filing"
Stored data by "Image composition"
2) When installing AR-P15, the following information will be erased as well.
Storage Job
Private Job
User information and Template information of Private Scan
Histories of Print and Scan
From July 2003 production
ROM
System ROM UI ROM
Main ROM
Laser
ROM
Scanner
ROM
PFC ROM
RADF ROM
Version
009
009
009
13
08
08
07
03
Changed problems
1) In RADF mixed paper size mode, in the case of copying with the combination such as LT-R and
Legal (or A4-R and FOLIO) in the mixed size document mode APS, RADF controller performed
reversing a document like the reading process of a duplex document in order to detect the
document correctly so that the speed of reading a document delayed. It was corrected.
2) When discharging papers with attaching the finisher, Shift process was changed not to let
discharged copies overlap among jobs.
3) When setting the magazine sort and Nin1, the display showed wrong magnification for the selected
paper.
Therefore, it was changed to renew the magnification after inputting the document in the case that
such mode was set.
4) Glazing stripe in the image due to grease of the cleaning roller was improved.
Spec change
1) 08 codes for controlling the temperature of the pressure roller were added.
(08-844-846 were added)
2) When a sheet is not set in the manual feed tray, the icon will be gray out in fear of touching the
icon of the manual feed tray in the special menu. (In the case of using the manual feed tray, the
setting is performed after putting the sheet, therefore if there is no sheet on the tray, the manual
feed tray related setting are now cannot be changed in order to prevent the mis-operation.)
3) 08 code for canceling the input number limit of continued original icon in a copy job using RADF
was added. (In 08-333 parameter, 2 was added)
4) In the case of copying with a cassette set as for the special paper, the cassette will be out of
target of auto cassette switch.
Note) These have been included from the version combination above-mentioned or later.
Addition and change to [Service hand book] following this upgrading.
1. Change of the setting mode (08)
Setting mode (08)
Code
Name
Default
Acceptable value
Contents
Before
change
0
0^1
0:9 times  1:4 times
333
Continued original
input number of time
After
change
0
0^2
0:9 times  1:4 times  2: Unlimited
AR568
Sharp Electronics (UK) Ltd., Technical Services Group
2. Addition of the setting mode(08)
Setting mode (08)
Code
Items adjusted
Target
Functions
Default
Acceptab
le value
Contents
Operating
Procedure
844
Transition time of
low speed pre-run
in Ready (Pressure
roller)
ALL
7
0^12
0:Invalid  1:5 min.  2:10 min.
3:20 min.  4:30 min.  5:40 min.
6:50 min.  7:60 min.  8:70 min.
9:80 min.  10:90 min.  11:100 min.
12:120 min.
1
845
Starting
temperature of low
speed pre-run in
Ready (Pressure
roller)
(When "08-844" is
valid)
ALL
9
0^16
0:50   1:55   2:60   3:65
4:70   5:75   6:80   7:85
8:90   9:95   10:100
11:105   12:110   13:115
14:120   15:125   16:130
846
Stopping
temperature of low
speed pre-run in
Ready (Pressure
roller) (When "08-
844" is valid)
ALL
5
0^9
0:+5   1:+10   2:+15  3:+20
4:+25   5:+30  6:+35
7:+40   8:+45  9:+50
1
Current parts
New parts
Ref.
No.
Model
name
Version P/G No.
Parts code
Parts code
Price
rank
Parts name
Effective
time
Inter-
change
-
ability
Note
201-15
0N6LA07749500
SYSTEM
ROM 009R1
201-16
0N6LA07751500
SYSTEM ROM
009R2
201-17
0N6LA07752500
BW
UI ROM 009
201-11
0N6LA07737800
MAIN ROM 13
201-12
0N6LA07738500
SCANNER
ROM 08
201-13
0N6LA07739500
LASER ROM 08
201-14
0N6LA07740400
BR
PFC ROM 07
AR-651
AR-810
ALL
201-18
---
0N6LA14813000
BT
RADF ROM 03
2003/7
3
<Interchange>
1. Interchangeable.
4. Not interchangeable.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
5. Interchangeable if replaced with same types of
related parts in use.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
6. Others.
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
Page of 10
Display

Download Sharp AR-651 (serv.man48) Technical Bulletin

Here you can read online and download Sharp AR-651 (serv.man48) Technical Bulletin in PDF. AR-651 (serv.man48) technical bulletin will guide through the process and help you recover, restore, fix, disassemble and repair Sharp AR-651 (serv.man48) Copying Equipment. Information contained in service manuals typically includes schematics / circuit diagrams, wiring diagrams, block diagrams, printed wiring boards, exploded views, parts list, disassembly / assembly, pcb.