Read Sony ZS-M30 Service Manual online
32
ZS-M30
46
XRAS
O
Row address strobe signal output to the D-RAM (IC505) “L” active
47
XWE
O
Write enable signal output to the D-RAM (IC505) “L” active
48
D1
I/O
49
D0
I/O
Two-way data bus with the D-RAM (IC505)
50
D2
I/O
51
D3
I/O
52
MVCI
I (S) Digital in PLL oscillation input from the external VCO Not used (fixed at “L”)
53
ASYO
O
Playback EFM full-swing output terminal
54
ASYI
I (A) Playback EFM asymmetry comparator voltage input terminal
55
AVDD
—
Power supply terminal (+3.3 V) (analog system)
56
BIAS
I (A) Playback EFM asymmetry circuit constant current input terminal
57
RFI
I (A) Playback EFM RF signal input from the CXA2523AR (IC502)
58
AVSS
—
Ground terminal (analog system)
59
PCO
O (3) Phase comparison output for master clock of the recording/playback EFM master PLL
60
FILI
I (A) Filter input for master clock of the recording/playback master PLL
61
FILO
O (A) Filter output for master clock of the recording/playback master PLL
62
CLTV
I (A) Internal VCO control voltage input of the recording/playback master PLL
63
PEAK
I (A) Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC502)
64
BOTM
I (A) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC502)
65
ABCD
I (A) Light amount signal (ABCD) input form the CXA2523AR (IC502)
66
FE
I (A) Focus error signal input from the CXA2523AR (IC502)
67
AUX1
I (A) Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC502)
68
VC
I (A) Middle point voltage (+1.65 V) input from the CXA2523AR (IC502)
69
ADIO
O (A) Monitor output of the A/D converter input signal Not used (open)
70
AVDD
—
Power supply terminal (+3.3 V) (analog system)
71
ADRT
I (A) A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
72
ADRB
I (A) A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
73
AVSS
—
Ground terminal (analog system)
74
SE
I (A) Sled error signal input from the CXA2523AR (IC502)
75
TE
I (A) Tracking error signal input from the CXA2523AR (IC502)
76
DCHG
I (A) Connected to the +3.3 V power supply
77
APC
I (A) Error signal input for the laser automatic power control Not used (fixed at “H”)
78
ADFG
I (S) ADIP duplex FM signal (22.05 kHz
±
1 kHz) input from the CXA2523AR (IC502)
79
F0CNT
O
Filter f0 control signal output to the CXA2523AR (IC502)
80
XLRF
O
Serial data latch pulse signal output to the CXA2523AR (IC502)
81
CKRF
O
Serial data transfer clock signal output to the CXA2523AR (IC502)
82
DTRF
O
Writing serial data output to the CXA2523AR (IC502)
83
APCREF
O
Control signal output to the reference voltage generator circuit for the laser automatic
powercontrol
84
TESTO
—
Not used (OPEN)
85
TRDR
O
Tracking servo drive PWM signal (–) output to the BH6511FS (IC501)
86
TFDR
O
Tracking servo drive PWM signal (+) output to the BH6511FS (IC501)
87
DVDD
—
Power supply terminal (+3.3 V) (digital system)
88
FFDR
O
Focus servo drive PWM signal (+) output to the BH6511FS (IC501)
89
FRDR
O
Focus servo drive PWM signal (–) output to the BH6511FS (IC501)
90
FS4
O
Clock signal (176.4 kHz) output terminal (X’tal system) Not used (open)
Pin No.
Pin Name
I/O
Pin Description
Click on the first or last page to see other ZS-M30 service manuals if exist.