Read Sony STR-DN1060 / STR-DN860 Service Manual online
STR-DN860/DN1060
8
NOTE OF REPLACING MB-1409 BOARD OR WLAN/
BT COMBO CARD
When the MB-1409 board or WLAN/BT COMBO card are
replaced, please execute the below service mode.
Procedure:
While pressing [DISPLAY] button, press and release the [MUSIC],
[A.F.D/2CH], [MOVIE] button in order, the message “SERVICE
IN” appears.
Next, go to service menu and execute “[1] Bluetooth Enable” and
“[3] Write Bluetooth device address to Registry”.
Finally check one touch NFC listening function at normal power
on.
Note: The operation in this mode must use a remote commander
BT COMBO CARD
When the MB-1409 board or WLAN/BT COMBO card are
replaced, please execute the below service mode.
Procedure:
While pressing [DISPLAY] button, press and release the [MUSIC],
[A.F.D/2CH], [MOVIE] button in order, the message “SERVICE
IN” appears.
Next, go to service menu and execute “[1] Bluetooth Enable” and
“[3] Write Bluetooth device address to Registry”.
Finally check one touch NFC listening function at normal power
on.
Note: The operation in this mode must use a remote commander
and TV monitor.
1. Connect this unit with TV monitor.
2. Press the [
2. Press the [
?/1
] button to turn the power on.
3. While pressing [DISPLAY] button, press and release the
[MUSIC], [A.F.D/2CH], [MOVIE] button in order, the
message “SERVICE IN” appears.
message “SERVICE IN” appears.
4. Enter the SVC service mode. The OSD menu on TV monitor
can be operated by remote commander.
5. Press
[m] and Enter Diag.
6. Press
[,] and Enter Bluetooth Device Test (Screen 1).
7. Enter [1] Bluetooth Enable, wait until the display show
“ Status : Bluetooth Enable Successful ” (Screen 2).
8. Enter [3] Write Bluetooth device address to Registry, wait until
the display show “Bluetooth Device Address” and “Status :
Write Successfull” (Screen 3).
Write Successfull” (Screen 3).
9. Press the [RETURN] button on the remote commander to
select “Wireless LAN Test” (Screen 4).
10. Press the [ ] button on the remote commander to select
“[5] Write P2P address to Registry”.
11. Press the [ ] button on the remote commander, wait until the
display show “Status: Write Successful!” (Screen 5).
12. Press the [m] button on the remote commander to select
“(6) P2P Registry Check” (Screen 6).
13. Press the [ ] button on the remote commander to check the
P2P device address is the same as shown in Screen 5.
(Displayed characters/values in the following fi gure are
example)
14. Press the [RETURN] button on the remote commander and
select Factory Initialize (go to Screen 7).
15. The set will turn off automatically.
Diag
Category:
Bluetooth Device Test
Diag
Category: Bluetooth Device Test
[1] Bluetooth Enable
[2] Bluetooth Disable
[3] Write Bluetooth device address to Registry
[4] Bluetooth Inquiry Test
[3] Write Bluetooth device address to Registry
[4] Bluetooth Inquiry Test
Status : Bluetooth Enable Successful!
HELP: [UP] [DOWN] [ENT] [RET]
(Screen 1)
(Screen 2)
Diag
Category:
Wireless LAN Test
Diag
Category: Wireless LAN Test
[1] Show WLAN HwInfo
[2] Connect to AccessPoint
[3] Start Display RSSI Value
[4] Start Ping Test
[1] Show WLAN HwInfo
[2] Connect to AccessPoint
[3] Start Display RSSI Value
[4] Start Ping Test
[5] Write P2P address to Registry
[6] P2P Registry Check
P2P device address : xx:xx:xx:xx:xx:xx
Status : Write Successful!
Status : Write Fail!
Status : Write Successful!
Status : Write Fail!
Diag
Category: Wireless LAN Test
[1] Show WLAN HwInfo
[2] Connect to AccessPoint
[3] Start Display RSSI Value
[4] Start Ping Test
[5] Write P2P address to Registry
[1] Show WLAN HwInfo
[2] Connect to AccessPoint
[3] Start Display RSSI Value
[4] Start Ping Test
[5] Write P2P address to Registry
[6] P2P Registry Check
P2P device address : xx:xx:xx:xx:xx:xx
HELP: [UP] [DOWN] [ENT] [RET]
(Screen 4)
(Screen 5)
(Screen 6)
(Screen 7)
(Screen 3)
Diag
Category: Bluetooth Device Test
[1] Bluetooth Enable
[2] Bluetooth Disable
[1] Bluetooth Enable
[2] Bluetooth Disable
[3] Write Bluetooth device address to Registry
[4] Bluetooth Inquiry Test
Bluetooth device address : 00:01:36:23:FD:CF
Status : Write Successful!
Status : Write Successful!
HELP: [UP] [DOWN] [ENT] [RET]
Service Mode Menu
[1] Diag
[2] Log
[2] Log
[3] Factory Initialize
[4] Network --> Not Support In This Model
[5] Version Up
[6] System Information
[7] EMC Test Mode
[8] Drive --> Not Support In This Model
[5] Version Up
[6] System Information
[7] EMC Test Mode
[8] Drive --> Not Support In This Model
[9] HDD mode
[10] RF Test Mode
HELP: [DOWN] [ENT]
Click on the first or last page to see other STR-DN1060 / STR-DN860 service manuals if exist.