STR-DN1060, STR-DN860 - Sony Audio Service Manual (repair manual). Page 5

UNLEADED  SOLDER
Boards requiring use of unleaded solder are printed with the 
lead-free mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with 

the lead free mark due to their particular size)

Unleaded solder has the following characteristics.
•  Unleaded solder melts at a temperature about 40 °C higher 

than ordinary solder.

 

Ordinary soldering irons can be used but the iron tip has to be 
applied to the solder joint for a slightly longer time.

 

Soldering irons using a temperature regulator should be set to 
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if 

the heated tip is applied for too long, so be careful!

• Strong 

viscosity

 

Unleaded solder is more viscous (sticky, less prone to fl ow) 
than ordinary solder so use caution not to let solder bridges 
occur such as on IC pins, etc.

•  Usable with ordinary solder
 

It is best to use only unleaded solder but unleaded solder may 
also be added to ordinary solder.

NOTE  OF  REPLACING  THE  IC101,  IC102,  IC103,  IC110,  
IC301,  IC307,  IC308,  IC309,  IC310,  IC313,  IC2001,  
IC3700 (DN860),  IC5000,  IC5009,  IC5010,  IC6000 
(DN1060),  IC6501,  IC7100,  IC7400  AND  IC7440  ON  THE  
MB-1409  BOARD
IC101, IC102, IC103, IC110, IC301, IC307, IC308, IC309, IC310, 
IC313, IC2001, IC3700 (DN860), IC5000, IC5009, IC5010, 
IC6000 (DN1060), IC6501, IC7100, IC7400 and IC7440 on the 
MB-1409 board cannot exchange with single. When these parts 
on the MB-1409 board are damaged, exchange the entire mounted 
board.

NOTE  OF  REPLACING  THE  IC1906,  IC1912,  IC1913,  
IC1914  AND  IC1915  ON THE  DCDC  BOARD
IC1906, IC1912, IC1913, IC1914 and IC1915 on the DCDC board 
cannot exchange with single. When these parts on the DCDC 
board are damaged, exchange the entire mounted board.

NOTE  OF  REPLACING  THE  IC1236  ON  THE  MAIN  
BOARD
IC1236 on the MAIN board cannot exchange with single. When 
this part on the MAIN board is damaged, exchange the entire 
mounted board.

DN1060: US, Canadian

4-547-190-0[]

DN1060: AEP, UK

4-547-190-1[]

DN1060: Australian

4-547-190-2[]

DN860: US, Canadian

4-547-191-0[]

DN860: AEP, UK

4-547-191-1[]

DN860: Australian

4-547-191-2[]

DN860: Taiwan

4-547-191-3[]

DN1060: Singapore 

4-547-191-5[]

NOTE  OF  REPLACING  THE  WLAN/BT  COMBO  CARD
When the WLAN/BT COMBO CARD is exchanged, the MAC 
address has been changed.
Please print and cut out the following explanations, and return it 
with the unit that complete the repair.

MAC address of this receiver has been changed by 
this repair.
The customer who use the MAC address fi ltering 
function of connected access point equipment please 
set it again.
MAC address is possible to confi rm on the System 
Information.
screen of this unit.
Please refer to “Adjusting Settings” ---> “Network 
Settings” on the Help Guide for details.

Help Guide Links :

AEP, UK Models : http://rd1.sony.net/help/ha/strdn10686/h_eu/

Except AEP,  

: http://rd1.sony.net/help/ha/strdn10686/h_zz/

UK Models

Please check the basic operation for wired LAN, Wireless 
LAN and USB after the repair completed.

NOTE  OF  DELETING  THE  PRODUCT  REGISTRATION 
ON  SEN  (INTERNET  MUSIC  SERVICES)
It is needed to delete the product registration on SEN (INTERNET 
MUSIC SERVICES) by checking the “Device ID” which have 12 
digits hexadecimal number. The procedure of checking “Device 
ID” can be followed as below:

1.  Press [HOME] key of the remote commander, the message 

“HOME MENU” appears.

2.  Select “Setup” and press [ENTER] key.
3.  Select “System Settings” and press [ENTER] key.
4.  Select “System Information” and press [ENTER] key.
5.  Device ID will shown on the display.
 

Device ID: XXXX XXXX XXXX  (12 digits hexadecimal 
number).

If it is needed to delete the customer’s registration, please contact 
the Service Headquarter with Device ID information.