Read Sony STR-DN1030 Service Manual online
STR-DN1030
13
SECTION 3
TEST MODE
TUNER AM STEP CHANGE MODE
(US, Canadian, Brazilian and Mexican models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
(US, Canadian, Brazilian and Mexican models)
Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
Procedure:
1. Press the [
?/1
] button to turn on the main power.
2. Turn the [INPUT SELECTOR] button to select the “AM
TUNER”.
3. Press the [
?/1
] button to turn off the main power.
4. While pressing the [TUNING MODE] button, press the [
?/1
]
button to turn on the main power.
5. Either the message “AM 9k Step” or “AM10k Step” appears,
select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
All fl uorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
Procedure:
While depressing the [SPEAKERS] and the [DIMMER] buttons
simultaneously, press the [
All fl uorescent segments are tested.
When this test is activated, all segments light on at the same time,
then each segment lights on one after another.
Procedure:
While depressing the [SPEAKERS] and the [DIMMER] buttons
simultaneously, press the [
?/1
] button to turn on the main power.
1. ALL segments light on.
2. Press the [DISPLAY] control, confi rm display.
3. Press the [DISPLAY] control, confi rm display.
4. Press the [DISPLAY] control, all segments light off.
SOUND FIELD CLEAR MODE
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
The preset sound fi eld is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [MUSIC] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. CLEAR” appears and initialization is per-
formed.
KEY CHECK MODE
Button check.
Procedure:
1. While pressing the [SPEAKERS] and the [INPUT MODE]
Button check.
Procedure:
1. While pressing the [SPEAKERS] and the [INPUT MODE]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “REST 13” appears.
Every pressing of any button other than the [
?/1
] counts down
the buttons. The buttons which are already counted once are
not counted again. When all buttons are pressed “REST 00”
displayed.
not counted again. When all buttons are pressed “REST 00”
displayed.
INITIALIZE MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing the [TUNING MODE] and [DIMMER] but-
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
(a) SHIPMENT MODE
Procedure:
1. While pressing the [TUNING MODE] and [DIMMER] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are re-
set to the default values.
3. When done, the message “CLEARED !” appears, the set will
power off.
(b) ALL CLEAR INITIALIZE
Procedure:
1. While pressing the [TUNING MODE] and [INPUT MODE]
Procedure:
1. While pressing the [TUNING MODE] and [INPUT MODE]
buttons, press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears and the memories are
reset to the default values.
3. When done, the message “CLEARED !” appears.
(c) USER INITIALIZE
Procedure:
1. Hold the [
(c) USER INITIALIZE
Procedure:
1. Hold the [
?/1
] for 5 seconds.
2. The message “CLEARING” appears on the display.
3. After a few seconds, “CLEARED !” appears.
3. After a few seconds, “CLEARED !” appears.
SWAP MODE
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [TUNING MODE] and [MOVIE(HD-
The signal will be swap to all channel so that all speaker will have
sound output.
Procedure:
1. While pressing the [TUNING MODE] and [MOVIE(HD-
D.C.S.)] buttons, press the [
?/1
] button to turn on the main
power.
2. The message “SWAP MODE” appears (No change while dis-
played).
PROTECTOR EVER MODE
This mode switch off the protector to investigate the cause of the
protector.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
This mode switch off the protector to investigate the cause of the
protector.
Procedure:
1. While pressing the [TONE MODE] and [A.F.D.] buttons,
press the [
?/1
] button to turn on the main power.
2. “PROTEVER” appears and switch off the set.
SOFTWARE VERSION DISPLAY MODE
The software version is displayed.
Procedure:
1. While pressing the [TUNING MODE] and [DISPLAY] but-
The software version is displayed.
Procedure:
1. While pressing the [TUNING MODE] and [DISPLAY] but-
tons, press the [
?/1
] button to turn on the main power.
2. The message “N1 ** Mx.xx” appears. This is main micro-
processor version.
**: destination, x.xx: software version
3. Press the [DISPLAY] button on the remote commander, HDMI
micro-processor version or DSP fi rmware version is changed.
VIDEO micro-processor version “H. Ver x.xx” appears.
DSP
fi rmware version “S. Ver x.xx” appears.
Hudson
II
fi rmware version “F. Ver x.xx” appears.
NETWORK
fi rmware version “N. Ver x.xx” appears.
TUNER
fi rmware version “T.Ver x.xx” appears.
DCAC TEST MODE
Procedure:
1. While pressing the [TONE MODE] and the [MOVIE (HD-
Procedure:
1. While pressing the [TONE MODE] and the [MOVIE (HD-
D.C.S.)] buttons, press the [
?/1
] button to turn on the main
power.
2. The message “SOURCE” or “MIC” appears.
SOURCE: normal mode
MIC: mode that output audio from mic input
SW
LH
RH
S
SL
SR
L
C
R
SBL SB SBR
USB HDMI COAX OPT PARTY ARC
D.L.L.
UPDATE D.RANGE A.P.M. ST AAC
D.C.A.C. EQ RDS NIGHT MEM DTS – HD
DTS – ES
LPCM SP A B
MSTR
MHz
k Hz
dB m
–
SLEEP
HDMIOUT
BLUETOOTH
ZONE 2 3
D + EX
HD
True
LFE
PLII
x z
A + B
NEO: 6
BI AMP
HI RES LBR
SW
SL
SR
L
R
SB
USB HDMI COAX OPT PARTY
D.RANGE A.P.M. ST AAC
DTS – HD
DTS – ES
B
MSTR
MHz
dB m
–
SLEEP
HDMIOUT
BLUETOOTH
3
A + B
NEO: 6
BI AMP
HI RES LBR
LH
RH
S
C
SBL
SBR
ARC
D.L.L.
UPDATE
D.C.A.C. EQ RDS NIGHT MEM
LPCM SP A
k Hz
ZONE 2
D + EX
HD
True
PL
Ver. 1.1
Click on the first or last page to see other STR-DN1030 service manuals if exist.