Read Sony STR-DA5600ES Service Manual online
STR-DA5600ES
5
UPDATE OF SOFTWARE OF IC2501 ON THE CON-
TROL BOARD, IC3610 ON THE D-VIDEO BOARD,
IC5208 ON THE DSP BOARD, IC105 AND IC763 ON
THE DISPLAY BOARD
Perform operation of the following when the update of software
of the IC2501 on the CONTROL board, IC3610 on the D-VIDEO
board, IC5208 on the DSP board, IC105 and IC763 on the DIS-
PLAY board are necessary.
TROL BOARD, IC3610 ON THE D-VIDEO BOARD,
IC5208 ON THE DSP BOARD, IC105 AND IC763 ON
THE DISPLAY BOARD
Perform operation of the following when the update of software
of the IC2501 on the CONTROL board, IC3610 on the D-VIDEO
board, IC5208 on the DSP board, IC105 and IC763 on the DIS-
PLAY board are necessary.
Connect:
for PC
J1499
Procedure:
1. Connect J1499 on the MAIN board and PC by using the RS-
1. Connect J1499 on the MAIN board and PC by using the RS-
232C cable.
2. Turn on the main power.
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J1499 on the MAIN
3. The update is executed by using PC.
4. When the update ends, turn off the main power.
5. Remove the RS-232C cable from the J1499 on the MAIN
board and PC.
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
1
Press
?/1 to turn off the
receiver.
2
While holding down the TONE
MODE and HDMI IN, press
MODE and HDMI IN, press
?/1
to turn on the receiver.
3
Release the TONE MODE and
HDMI IN after a few seconds.
HDMI IN after a few seconds.
After “MEMORY CLEARING...”
appears on the display for a while,
“MEMORY CLEARED.” appears.
All the settings you have changed or
adjusted are reset to the initial settings.
appears on the display for a while,
“MEMORY CLEARED.” appears.
All the settings you have changed or
adjusted are reset to the initial settings.
Note
It takes about 30 seconds for the memory to be
cleared completely. Do not turn the receiver off until
“MEMORY CLEARED.” appears on the display.
cleared completely. Do not turn the receiver off until
“MEMORY CLEARED.” appears on the display.
Performing initial setup
operations
operations
?/1
TONE MODE
HDMI IN
If there is a malfunction, the display shows a
code of two numbers and a message. You can
check the status of the system by the message.
See the following table to solve the problem. If
any problem persists, consult your nearest
Sony dealer.
code of two numbers and a message. You can
check the status of the system by the message.
See the following table to solve the problem. If
any problem persists, consult your nearest
Sony dealer.
PROTECTOR
The upper panel of the receiver is covered
with something. The receiver will
automatically turn off after a few seconds.
Remove the object covering the upper panel
of the receiver and turn on the power again.
with something. The receiver will
automatically turn off after a few seconds.
Remove the object covering the upper panel
of the receiver and turn on the power again.
SPEAKER SHORTED
Irregular current is output to the speakers
due to a short circuit on the speaker
terminals. The receiver will automatically
turn off after a few seconds. Check the
connection of the speakers and turn on the
power again.
due to a short circuit on the speaker
terminals. The receiver will automatically
turn off after a few seconds. Check the
connection of the speakers and turn on the
power again.
Error messages
CONFIRMATION OF NETWORK OPERATION
Note: When this confi rmation is executed, IP address is changed.
Necessary machinery and materials:
• PC (Windows XP/Vista)
• Router
• PC (Windows XP/Vista)
• Router
(Transmission rate is 100 Mbps or more, built-in DHCP server
function)
function)
• Two LAN cables
(Category 5 cable, normal type or shield type)
• Monitor
• Multifunction remote commander
• Multifunction remote commander
(RM-AAL021 or RM-AAL022)
Connection:
(The router need not be connected with the internet)
(The router need not be connected with the internet)
LAN cable
router
PC
set
monitor
NETWORK board
LAN jack (CN501)
LAN jack (CN501)
A VIDEO board
MONITOR VIDEO OUT
jack (J6001) or
D-VIDEO board
HDMI OUT A connector
(CN3511)
MONITOR VIDEO OUT
jack (J6001) or
D-VIDEO board
HDMI OUT A connector
(CN3511)
VIDEO cable or
HDMI cable
HDMI cable
Procedure:
1. The setting of LAN of PC is setting to the automatic IP address
1. The setting of LAN of PC is setting to the automatic IP address
assignment.
It changes to the setting that displays the image in the monitor.
2. The above-mentioned connection is done.
3. The power supply of the router is turn on, next, the power sup-
3. The power supply of the router is turn on, next, the power sup-
ply of PC and the set is turn on.
4. Press the [GUI MODE] button of the remote commander, the
GUI screen is displayed in the monitor.
5. The “Settings” is selected on the GUI screen.
Next, “Network Setup” in “Network” is selected, and press the
[ ] button of remote commander.
[ ] button of remote commander.
6. When the network setting is a unsetting, “Next” is selected on
the screen of “Start Network function initial Setup Wizard”,
and press the [ ] button of remote commander.
and press the [ ] button of remote commander.
When it has already been set, “Internet Setup” is selected on
the screen of “Select Setup item”, and press the [ ] button of
remote commander.
the screen of “Select Setup item”, and press the [ ] button of
remote commander.
7. “Connect Automatically (DHCP)” is selected on the screen of
“Confi gures network settings automatically or manually”, and
press the [ ] button of remote commander.
press the [ ] button of remote commander.
8. The automatically connect function operates, it becomes the
screen of “Success!” tens of seconds later, the confi rmation
ends when “Finish” is selected.
ends when “Finish” is selected.
NOTE OF REPLACING THE NETWORK BOARD
When the NETWORK board is exchanged, the MAC address has
been changed.
Please print and cut out the following explanations, and return it
with the set that completes the repair.
When the NETWORK board is exchanged, the MAC address has
been changed.
Please print and cut out the following explanations, and return it
with the set that completes the repair.
MAC address of this receiver has been changed by this repair.
The customer who uses the MAC address fi ltering function of
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the network setting screen of ES
utility of an attachment application.
The customer who uses the MAC address fi ltering function of
connected access point equipment please set it again. MAC ad-
dress is possible to confi rm it on the network setting screen of ES
utility of an attachment application.
Click on the first or last page to see other STR-DA5600ES service manuals if exist.