Read Sony SS-NA5ES Service Manual online
SS-NA5ES
6
2-4. LOUDSPEAKER (1.9 cm) (ASSIST TWEETER) (SP1, SP2)
3 Lift up the loudspeaker
(1.9 cm) (assist tweeter:
upper side) (SP1).
5 loudspeaker (1.9 cm)
(assist
tweeter:
upper side) (SP1)
loudspeaker (1.9 cm) (assist tweeter: upper side)
(SP1)
(SP1)
loudspeaker (1.9 cm)
(assist tweeter:
upper side) (SP1)
“–” wire (black)
(assist tweeter:
upper side) (SP1)
“–” wire (black)
5 loudspeaker (1.9 cm)
(assist
tweeter:
lower side) (SP2)
loudspeaker (1.9 cm) (assist tweeter: lower side)
(SP2)
(SP2)
loudspeaker (1.9 cm)
(assist tweeter:
lower side) (SP2)
“+” wire (gray)
(assist tweeter:
lower side) (SP2)
“+” wire (gray)
tweeter assy
3 Lift up the loudspeaker
(1.9 cm) (assist tweeter:
lower side) (SP2).
speaker (2.5 cm) assy
(SP3)
(SP3)
speaker (2.5 cm) assy
(SP3)
(SP3)
4 packing (C)
packing (C) boss
packing (C) boss
4 packing (C)
convex
part
part
Note 2: When disassembling loudspeakers
(1.9 cm) (assist tweeter) (SP1, SP2),
place a stand etc. under tweeter assy
and be careful not to crush the convex
part of a speaker (2.5 cm) assy (SP3).
Note 9: When disassembling loudspeakers (1.9 cm) (assist tweeter)
(SP1, SP2), be sure to perform the polar check of "+" and
"í", to make "+" into the upper left side and to attach it, as
shown in the following figure.
Note 8: Check packing (C) not having
overlapped or not having run
aground.
Note 7: Do not touch the
convex
convex
part.
stand
stand
Note 10: Check that the connection mistake or insertion of a wire are not imperfect.
Note 11: Insert the terminal straightly.
Note 12: The arrangement of a wire should check that left side is gray and that right side is black.
Note 13: Check that a wire is on a speaker (2.5 cm) assy (SP3).
Note 11: Insert the terminal straightly.
Note 12: The arrangement of a wire should check that left side is gray and that right side is black.
Note 13: Check that a wire is on a speaker (2.5 cm) assy (SP3).
2 two screws (BV B3.5 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: .5 .5 1m
2 two screws (BV B3.5 u 10)
Note
3: When tightening screws, be
careful not to put the wire of
loudspeakers.
Note
4: Check that the screw has not
floated or it is not slanting.
Note
5: Check that packing (C) has
not overflowed the edge of
loudspeakers.
Note
6: tightening torque: .5 .5 1m
,QVWDOOHGSRVLWLRQRIORXGVSHDNHUFPDVVLVWWZHHWHU6363
,QVWDOOHGSRVLWLRQRISDFNLQJ&
1 terminal
(gray)
1 terminal
(black)
–,QQHUVLGHYLHZ–
–,QQHUERWWRPVLGHYLHZ–
–,QQHUVLGHYLHZ–
“+”
“–”
Note 1: When exchanging the loudspeaker (1.9 cm) (assist tweeter) (SP1, SP2),
refer to “NOTE THE SPEAKER UNITS REPLACING” on page 2.
Click on the first or last page to see other SS-NA5ES service manuals if exist.