Read Sony SA-WCT260 Service Manual online
SA-WCT260
SA-WCT260
14
14
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
• f : Internal component.
• 2 : Nonfl ammable resistor.
• 5 : Fusible resistor.
• C : Panel designation.
• 2 : Nonfl ammable resistor.
• 5 : Fusible resistor.
• C : Panel designation.
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
(In addition to this, the necessary note is printed in each block.)
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : POWER ON
• Voltages are taken with VOM (Input impedance 10 M
• Voltages are taken with VOM (Input impedance 10 M
).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F :
F :
AUDIO
(ANALOG)
J :
AUDIO
(DIGITAL)
• Abbreviation
BR
BR
: Brazilian model
CND : Canadian model
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• f : Internal component.
•
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
• f : Internal component.
•
: Pattern from the side which enables seeing.
(The other layers’ patterns are not indicated.)
Note:
The components identi-
fi
The components identi-
fi
ed by mark 0 or dotted
line with mark 0 are criti-
cal for safety.
Replace only with part
number specifi ed.
cal for safety.
Replace only with part
number specifi ed.
Note:
Les composants identifi és
par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par
une pièce portant le nu-
méro spécifi é.
Les composants identifi és
par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par
une pièce portant le nu-
méro spécifi é.
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Abbreviation
BR
BR
: Brazilian model
CND : Canadian model
Note: When the complete SUB MAIN board is replaced, re-
fer to “NOTE OF REPLACING THE IC104 ON THE
SUB MAIN BOARD AND THE COMPLETE SUB
MAIN BOARD” on page 3.
SUB MAIN BOARD AND THE COMPLETE SUB
MAIN BOARD” on page 3.
Note: When the complete SUB MAIN board is replaced, re-
fer to “NOTE OF REPLACING THE IC104 ON THE
SUB MAIN BOARD AND THE COMPLETE SUB
MAIN BOARD” on page 3.
SUB MAIN BOARD AND THE COMPLETE SUB
MAIN BOARD” on page 3.
• Indication of transistor.
C
B
These are omitted.
E
Q
C E
B
These are omitted.
• Waveforms
– SUB MAIN Board –
1
IC100
7 (Xout)
1 V/DIV, 20 ns/DIV
50 ns
1.8 Vp-p
3
IC105
eh (XFSIIN)
1 V/DIV, 50 ns/DIV
82 ns
3.3 Vp-p
2
IC105
qf (XFSOOUT)
500 mV/DIV, 10 ns/DIV
20.4 ns
1 Vp-p
4
IC105
rk (XFSOIN)
500 mV/DIV, 10 ns/DIV
20.6 ns
0.8 Vp-p
5
IC107
2 (A)
100 mV/DIV, 10 ns/DIV
20.6 ns
0.2 Vp-p
Caution:
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Pattern face side:
(SIDE B)
Parts face side:
(SIDE A)
Parts on the pattern face side seen
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
from the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Ver. 1.1
Click on the first or last page to see other SA-WCT260 service manuals if exist.