Read Sony PCM-D100 Service Manual online
PCM-D100
26
4-11. Sircs Check
Operation of remote commander keys can be checked.
Operation of remote commander keys can be checked.
Note 1: This check requires remote commander and receiver unit.
Procedure:
1. Receiver unit is connected to the main unit.
1. Receiver unit is connected to the main unit.
Receiver unit
To REMOTE jack
Remote sensor
2. Enter the test mode.
(Refer to “SETTING THE TEST MODE” on page 22)
3. Press the [v] or [V] keys to select the “Sircs Check”, and press
the [N] key.
4. Whenever target keys of remote commander are pressed, the
button count decreases.
Note 2: Although keys of unit are also counted, but there is no problem.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
<Sircs Check>
Channel 1 – – –>
Channel 2 – –
Channel 3 – –
REMAIN : 07
Channel 1 – – –>
Channel 2 – –
Channel 3 – –
REMAIN : 07
LCD Display
KEY – –
Button count
Confirmed key name
Confirmed key name
Target keys of remote commander (Channel 1) :
[x STOP], [z REC], [X PAUSE], [T-MARK], [N PLAY],
[>], [.]
[>], [.]
Target keys of remote commander (Channel 2) :
[x STOP]
Target keys of remote commander (Channel 3) :
[x STOP]
The LCD backlight is turned on for 0.5 second at the time of
keys decision.
keys decision.
Change method of channel of the remote command-
er:
er:
While pressing the [SET] button on the remote commander,
press the [CH1], [CH2] or [CH3] button on the remote com-
mander.
press the [CH1], [CH2] or [CH3] button on the remote com-
mander.
The change of “Channel 1” to “Channel 3” of main unit is
performed automatically.
performed automatically.
5. All of “Channel 1” to “Channel 3” check that the message
“OK” appears.
Releasing method:
Press the [x STOP] key, return to test mode menu.
Press the [x STOP] key, return to test mode menu.
4-12. Keychk+Factory
Ship
Operation of keys and switches can be checked, and this unit can
return to the factory shipment settings (LCD contrast is not initial-
ized).
return to the factory shipment settings (LCD contrast is not initial-
ized).
Note: It cannot move to other modes from this mode.
Procedure:
1. Enter the test mode.
1. Enter the test mode.
(Refer to “SETTING THE TEST MODE” on page 22)
2. Press
the
[
v
] or [
V
] keys to select the “Keychk+Factory Ship”,
and press the [
N
] key.
3. Whenever any keys of this unit are pressed or any switches of
this unit are slid, the button count decreases.
(Displayed characters/values in the following fi gure are ex-
ample)
ample)
<Keychk+Factory Ship>
REMAIN : 22
KEY OFF
KEY OFF
LCD Display
Button count
Confirmed key name
Target keys:
[x STOP], [OPTION], [F2], [v], [N], [F1], [HOME/BACK],
[.], [>], [V], [T-MARK], [X PAUSE], [LIGHT], [z
REC]
[.], [>], [V], [T-MARK], [X PAUSE], [LIGHT], [z
REC]
Target switches:
[HOLD] (ON/OFF), [POWER] (ON/OFF), INPUT switch
(MIC/LINE), X-Y position (Direction of the microphone: in-
side/outside)
(MIC/LINE), X-Y position (Direction of the microphone: in-
side/outside)
The LCD backlight is turned on for 0.5 second at the time of
keys decision.
keys decision.
4. After all the keys and switches are decided, initialization is
performed.
5. “OK” is displayed, and this unit reboots.
<Keychk+Factory Ship>
Execute...
LCD Display
OK
Click on the first or last page to see other PCM-D100 service manuals if exist.