Read Sony ICD-BM1 / ICD-BM1PRO Service Manual online
7
ICD-BM1/BM1PRO
Basic Operations
19
GB
Recording from Other Equipment
To record sound of other equipment with the IC recorder, connect the MIC
(microphone) jack of the IC recorder to the earphone jack of other
equipment (tape recorder etc.) by using an audio connecting cable.
(microphone) jack of the IC recorder to the earphone jack of other
equipment (tape recorder etc.) by using an audio connecting cable.
Notes
• When the audio recording level is large, sound may be recorded
• When the audio recording level is large, sound may be recorded
interrupted if you use an audio connecting cable without register. Use a
registered audio connecting cable.
registered audio connecting cable.
• When the audio recording level is small, do not use a registered audio
connecting cable.
Recording with Other Equipment
To record the sound of the IC recorder with other equipment, connect the
i
(headphones) jack of the IC recorder to the audio input connector
(minijack, stereo) of other equipment.
Tape recorder, etc.
mini-plug (stereo)
mini-plug (stereo)
20
GB
1
Press FOLDER.
2
Press the jog lever up or down (
>/
.
) to display the folder containing
the message you want to play back.
3
Press ENTER to select the folder.
To cancel the selection, press CANCEL.
Selected
folder
folder
Select the message number.
Selected message number
The number of
message in a folder
message in a folder
Press the jog lever up or down (
>/.
) to display
the desired message number.
Press up (
Press up (
>
): for next message number.
Press down (
.
): for previous message number.
Counter display*
Playing Back Messages
When playing back a previously recorded message, start from Step 1.
When playing back a message you have just finished recording, start from
Step 3.
When playing back a message you have just finished recording, start from
Step 3.
Select the folder.
1
FOLDER
ENTER
2
* The display selected with the DISPLAY button (page 26)
appears.
Basic Operations
21
GB
Slide the control key to STOP.
The unit stops at the current position. (When
the unit reaches to the end of the last
message in step 3, it stops at the end of the
last message.)
You can start an overwrite recording from
the point (page 15).
The unit stops at the current position. (When
the unit reaches to the end of the last
message in step 3, it stops at the end of the
last message.)
You can start an overwrite recording from
the point (page 15).
Stop playback.
4
Start playback.
1
Slide the control key to PLAY.
2
Adjust the volume with VOL +/– .
* The display selected with the DISPLAY button
(page 26) appears.
The unit plays back all the messages in a folder
continuously. At the end of each message, a beep
will sound.
continuously. At the end of each message, a beep
will sound.
When the unit reaches to the end of the last message in a folder, “MSG END” will
flash 3 times with a beep and playback stops. Move the control key to STOP.
flash 3 times with a beep and playback stops. Move the control key to STOP.
1
To listen from an ear receiver
Connect the supplied ear receiver to the
i
(headphones) jack. The built-in
speaker will be automatically disconnected.
1
To listen from an external speaker
Connect an active or passive speaker (not supplied) to the
i
(headphones) jack.
Note
Playback after the overwrite recording starts from the beginning of the message.
Playback after a stop starts from the point where you stopped playback.
Playback after a stop starts from the point where you stopped playback.
i
jack
OPR indicator
(lights in green during
playback)
(lights in green during
playback)
3
Counter display*
Continued
22
GB
Playing Back Messages (continued)
Other operations
To
Do this
go back to the beginning
Press the jog lever down (
.
)
of the current message*
once.**
go back to previous
Press the jog lever down (
.
)
messages*
repeatedly. (During stop mode,
keep the button pressed to go back
the messages continuously.)**
keep the button pressed to go back
the messages continuously.)**
skip to the next message*
Press the jog lever up (
>
) once.***
skip to the succeeding messages* Press the jog lever up (
>
)
repeatedly.***
*
These operations are for when EASY-S is set to OFF. For operations when
EASY-S is set to ON, see page 51.
EASY-S is set to ON, see page 51.
** If you do these operations at the beginning of the first message in a folder
during stop mode, the unit locates the end of the last message.
*** If you do these operations at the end of the last message in a folder during
stop mode, the unit locates the beginning of the first message.
Playing back a message rapidly or slowly in natural tone
— DPC (Digital Pitch Control)
— DPC (Digital Pitch Control)
When you adjust the playback speed with the DPC in the menu (pages 39
and 40), you can play back a message rapidly or slowing by sliding the
DPC switch to ON. When you set the playback speed faster or slower of
the normal speed, “FAST PLAY” or “SLOW PLAY” appears. You can
change the setting during playback.
and 40), you can play back a message rapidly or slowing by sliding the
DPC switch to ON. When you set the playback speed faster or slower of
the normal speed, “FAST PLAY” or “SLOW PLAY” appears. You can
change the setting during playback.
Searching forward/backward during playback (Cue/Review)
•
To search forward:
Keep pressing the jog lever up (
>
) during
playback and release it at the point you wish to resume playback.
•
To search backward:
Slide the control key to B.SPACE or keep pressing
the jog lever down (
.
) during playback and release it at the point you
wish to resume playback.
The unit searches at slow speed (unit of 4 seconds) with playback sound. It
is useful to check one word forward or behind. Then, if you keep pressing
the jog lever up or down, the unit starts to search at higher speed.
Release it at the point you want to resume playback.
is useful to check one word forward or behind. Then, if you keep pressing
the jog lever up or down, the unit starts to search at higher speed.
Release it at the point you want to resume playback.
Click on the first or last page to see other ICD-BM1 / ICD-BM1PRO service manuals if exist.