Read Sony HST-SE581 / SEN-R4820 / SEN-T481 Service Manual online
— 6 —
SECTION 3
MECHANICAL ADJUSTMENTS
SECTION 4
ELECTRICAL ADJUSTMENTS
PRECAUTION
1.
Clean the following parts with a denatured-alcohol-moistened
swab:
swab:
record/playback head
pinch roller
erase head
rubber belts
capstan
idlers
2.
Demagnetize the record/playback head with a head
demagnetizer.
demagnetizer.
3.
Do not use a magnetized screwdriver for the adjustments.
4.
After the adjustments, apply suitable locking compound to the
parts adjusted.
parts adjusted.
5.
The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
supply voltage unless otherwise noted.
• Torque Measurement
• Tape Tension Measurement
DECK SECTION
0 dB=0.775V
1.
Demagnetize the record/playback head with a head
demagnetizer. (Do not bring the head demagnetizer close to
the erase head.)
demagnetizer. (Do not bring the head demagnetizer close to
the erase head.)
2.
Do not use a magnetized screwdriver for the adjustments.
3.
After the adjustments, apply suitable locking compound to the
parts adjust.
parts adjust.
4.
The adjustments should be performed with the rated power
supply voltage unless otherwise noted.
supply voltage unless otherwise noted.
5.
The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit
adjustment.)
6.
The adjustments should be performed for both L-CH and R-
ch.
ch.
7.
Switches and controls should be set as follows unless otherwise
specified.
specified.
8.
Set to test mode. (While pressing the DUBBING SPEED
HIGH button, insert the AC outlet.)
HIGH button, insert the AC outlet.)
•
Test Tape
Record/Playback Head Azimuth Adjustment
DECK A
DECK B
Note :
Perform this adjustments for both decks. Remove the covers
of cassette holders.
Procedure:
1.
1.
Mode: Playback (FWD)
Mode
Torque Meter
Meter Reading
Forward
CQ-102C
36 to 61g•cm
(0.50 to 0.84 oz•inch)
Forward
CQ-102C
2 to 6g•cm
Back Tension
(0.026 to 0.082 oz•inch)
Reverse
CQ-102RC
36 to 61g•cm
(0.50 to 0.84 oz•inch)
Reverse
CQ-102RC
2 to 6g•cm
Back Tension
(0.026 to 0.082 oz•inch)
FF, REW
CQ-201B
61 to 143g•cm
(0.85 to 1.98 oz•inch)
Mode
Tension Meter
Meter Reading
Forward
CQ-403A
more than 100 g
(3.53 oz•inch)
Reverse
CQ-403R
more than 100 g
(3.53 oz•inch)
Tape
Signal
Used for
P-4-A100
10 kHz, –10 dB
Azimuth Adjustment
WS-48B
3 kHz, 0dB
Tape Speed Adjustment
P-4-L300
315 Hz, 0dB
Level Adjustment
set
rear panel
VIDEO1
AUDIO OUT connector
(L: L-CH)
(R: R-CH)
AUDIO OUT connector
(L: L-CH)
(R: R-CH)
+
–
–
level meter
test tape
P-4-A100
(10 kHz, –10 dB)
P-4-A100
(10 kHz, –10 dB)
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
2.
Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
Click on the first or last page to see other HST-SE581 / SEN-R4820 / SEN-T481 service manuals if exist.