Read Sony HST-SE581 / SEN-R4820 / SEN-T481 Service Manual online
— 5 —
SECTION 2
TEST MODE
[Fluorescent Indicator Tube, LED All Lit, and Key Check Mode]
1. When the plug is inserted into the outlet while pressing the
1. When the plug is inserted into the outlet while pressing the
MEMORY SCAN button, the fluorescent indicator tube and
LED will light up completely.
LED will light up completely.
2. The mode changes as follows each time the BAND button and
WOOFER ON/OFF button are pressed together after 1.
Sequence of Service Modes
*1 For checking if the fluorescent indicator tube and LED are lit
completely
*2 Model name and destination are shown in the destination display
mode.
*3 When the KEY check mode is set, “KEY 0”is displayed on the
fluorescent indicator tube. Each press of the button is counted.
(This excludes the
(This excludes the
1/u button)
Buttons pressed once will not be counted when pressed again.
When all keys are pressed, “KEY END” appears.
When all keys are pressed, “KEY END” appears.
*4 When the AMP check mode is set, “AMP” is displayed on the
fluorescent indicator tube.
Select any desired mode by pressing the TONE or CENTER
or REAR or WOOFER button. After a mode is selected,
press any of the DOLBY or HALL or SIMULATED button
as shown below to change the amplification level.
Select any desired mode by pressing the TONE or CENTER
or REAR or WOOFER button. After a mode is selected,
press any of the DOLBY or HALL or SIMULATED button
as shown below to change the amplification level.
3. To exit the test mode, press the
1/u button, or press the p
(STOP) button of the deck A during the modes except the key
check mode.
check mode.
[TC test mode]
1. Insert a playback tape into the deck A and a record tape into
1. Insert a playback tape into the deck A and a record tape into
the deck B.
2. While the power cable is disconnected from AC outlet, press
the
1/u switch.
3. While pressing the DUBBING SPEED HIGH button, connect
the power cable to the AC outlet.
Operation
Audio dubbing from deck A to Deck B starts.
When the
When the
0 button or the ) button (during reverse
recording) of the deck B is pressed during dubbing, the tape
returns to the recording start point and playback starts.
When the DUBBING SPEED HIGH button is pressed during
dubbing, the high speed dubbing is performed.
returns to the recording start point and playback starts.
When the DUBBING SPEED HIGH button is pressed during
dubbing, the high speed dubbing is performed.
[TC aging mode]
1. Turn on the main power.
2. Press the TAPE button. Insert a playback tape into the deck
1. Turn on the main power.
2. Press the TAPE button. Insert a playback tape into the deck
A and a record tape into the deck B.
3. Set the DIRECTION switch to .
4. Press the WOOFER and
4. Press the WOOFER and
p (STOP) button of the deck A at
the same time to enter the aging mode.
Operation
TONE
CENTER
REAR
WOOFER
DOLBY
–10 dB
–15 dB
–15 dB
–24 dB
HALL
0 dB
0 dB
0 dB
0 dB
SIMULATED
+10 dB
+6 dB
+6 dB
+8 dB
Fluorescent Indicator
Tube and LED Check Mode
Tube and LED Check Mode
*1
Destination display mode
*2
•
Press the BAND button and
WOOFER ON/OFF button at the same time.
KEY check mode
*3
•
Press the BAND button and
WOOFER ON/OFF button at the same time.
•
Press the BAND button and
WOOFER ON/OFF button at the same time.
AMP check mode
*4
•
Press the BAND button and
WOOFER ON/OFF button at the same time.
These operations are repeated.
5. How to exit the TC aging mode.
Press any keys related to the TC deck.
[Backup Clear Mode]
1. While pressing the DOLBY key, connect the power cable to
1. While pressing the DOLBY key, connect the power cable to
the AC outlet. All preset data is cleared.
Deck A rewinds (REW) up to the tape top,
Deck B rewinds (REW) up to the tape top,
Deck A plays back (FWD) for one minute, then stops (STOP)
momentarily,
Deck A plays back (FWD) for three minutes,
Deck A runs in fast forward (F. FWD) up to tape end,
Deck A plays back (REV) for one minute, then stops (STOP)
momentarily,
Deck A plays back (REV) for three minutes,
Deck A runs in fast reverse (REV) up to tape top,
Deck B plays back (FWD) for one minute, then stops (PAUSE)
momentarily,
Deck B records (FWD. RECORD) for three minutes,
Deck B runs in fast forward (F. FWD) up to tape end,
Deck B plays back (REV) for one minute, then stops (PAUSE)
momentarily,
Deck B records (REV. RECORD) for three minutes,
Deck B runs in fast reverse (REV) up to tape end,
Deck B rewinds (REW) up to the tape top,
Deck A plays back (FWD) for one minute, then stops (STOP)
momentarily,
Deck A plays back (FWD) for three minutes,
Deck A runs in fast forward (F. FWD) up to tape end,
Deck A plays back (REV) for one minute, then stops (STOP)
momentarily,
Deck A plays back (REV) for three minutes,
Deck A runs in fast reverse (REV) up to tape top,
Deck B plays back (FWD) for one minute, then stops (PAUSE)
momentarily,
Deck B records (FWD. RECORD) for three minutes,
Deck B runs in fast forward (F. FWD) up to tape end,
Deck B plays back (REV) for one minute, then stops (PAUSE)
momentarily,
Deck B records (REV. RECORD) for three minutes,
Deck B runs in fast reverse (REV) up to tape end,
<Repeat>
Click on the first or last page to see other HST-SE581 / SEN-R4820 / SEN-T481 service manuals if exist.