HCD-SHAKE5, HCD-SHAKE6D (serv.man2) - Sony Audio Service Manual (repair manual). Page 15

[DVD COLOR SYSTEM MODE] (SHAKE6D)
•  This mode let you change the color system of the video output 

from PAL to NTSC or vice-versa.

1.  Press the [\/1] button to turn on the system.
2.  Press the [DVD/CD] button.
3.  Press the [ENTER] button and [LED COLOR] button 

simultaneously and hold for 3 seconds.

4.  The message “COLOR PAL” or “COLOR NTSC” appears on 

the fl uorescent indicator tube.

1.  Once the color system has been selected, the mode is fi xed 

there after. If you wish to change the mode again, perform the 
above item 3 again.

[DVD SERVICE MODE] (SHAKE6D)
•  This mode let you make diagnosis and adjustment easily by 

using the remote commander and the TV. The instructions, 
diagnostic results, etc. are given on the on-screen display.

 

Be sure to use the DVD disc that matches the signal standards 
of your region.

 

•  CD

YEDS-18 

(Part No.: 3-702-101-01)

 

 

PATD-012 

(Part No.: 4-225-203-01)

 

•  DVD SL (Single Layer)

NTSC :  HLX-503  (Part No.: J-6090-069-A)

 

  HLX-504  (Part No.: J-6090-088-A)

PAL : 

HLX-506  (Part No.: J-6090-077-A)

 

•  DVD DL (Double Layer)

NTSC :  HLX-501  (Part No.: J-6090-071-A)

 

  HLX-505  (Part No.: J-6090-089-A)

PAL : 

HLX-507  (Part No.: J-6090-078-A)

1.  Press the [\/1] button to turn on the system.
2.  Press the [DVD/CD] button.
3.  Press the [ENTER] button and [+/PRESET+] button 

simultaneously and hold 3 seconds.

4.  The message “SERVICE IN” appears on the fl uorescent 

indicator tube and the Top Menu of Remocon Diagnosis 
Menu appears on the on-screen display on the TV.

 

The display of the “Model Name” of the “Remocon Diagnosis 
Menu” change with the model and the destination. Refer to 
below on the model name.

 

STOMJRD : SHAKE-6D

 

*1: Changes depending on destination

5.  To execute each function, press its number by using numeric 

button on the remote commander.

6.  To release from this mode, press the [\/1] button to turn off 

the system.

 

In order to execute IOP measurement, the following standard 
procedures must be followed.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“2. Drive Manual Operation” by pressing the [2] button on 
the remote commander. The following screen appears on the 
on-screen display.

2.  Select “3. Manual Adjustment” by pressing the [3] button on 

the remote commander. The following screen appears on the 
on-screen display.

3.  Select “6. Iop:” by pressing the [6] button on the remote 

commander.

4.  Wait until a hexadecimal number appears in the on-screen 

display as below:

5. Convert data from hexadecimal to decimal by using 

conversion table.

6. Please 

fi nd the label on the rear of the BU (Base Unit).

 

The default IOP value is written in the label.

7.  Subtract between these two values.
8.  If the remainder is smaller than 93 (decimal), then it is OK.
 

However if the value is higher than 93, then the BU is defective 
and need to be change.

9.  Press the [RETURN] button on the remote commander to 

return to previous menu.

10.  Press the [0] button on the remote commander to return to the 

Top Menu of Remocon Diagnosis Menu.

11.  Press the [\/1] button to turn off the system.

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5.  USB Test Mode Setting

Model Name
IF-con
Syscon

: SHAKE6D_ XX 

*1

: Ver.  XX.XX (XXXX)
: Ver.  X.XXX

 

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu

 

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu