HCD-SHAKE33, HCD-SHAKE44, HCD-SHAKE55, HCD-SHAKE66, HCD-SHAKE77, HCD-SHAKE88 - Sony Audio Service Manual (repair manual). Page 2

Read Sony HCD-SHAKE33 / HCD-SHAKE44 / HCD-SHAKE55 / HCD-SHAKE66 / HCD-SHAKE77 / HCD-SHAKE88 Service Manual online

HCD-SHAKE33/SHAKE44/SHAKE55/SHAKE66/SHAKE77/SHAKE88
2
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, 
screws, and all other exposed metal parts for AC leakage. Check 
leakage as described below.
LEAKAGE  TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1.  A commercial leakage tester, such as the Simpson 229 or RCA
 
WT-540A. Follow the manufacturers’ instructions to use these
 instruments.
2.  A battery-operated AC milliammeter. The Data Precision 245
 
digital multimeter is suitable for this job.
3.  Measuring the voltage drop across a resistor by means of a
 
VOM or battery-operated AC voltmeter. The “limit” indication
 
is 0.75 V, so analog meters must have an accurate low-voltage
 
scale. The Simpson 250 and Sanwa SH-63Trd are examples
 
of a passive VOM that is suitable. Nearly all battery operated
 
digital multimeters that have a 2V AC range are suitable. (See
 Fig. 
A)
1.5 k
Ω
0.15 
μF
AC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
Fig. A.  Using an AC voltmeter to check AC leakage.
SAFETY-RELATED  COMPONENT  WARNING!
COMPONENTS  IDENTIFIED  BY  MARK  
0  OR  DOTTED  LINE  
WITH  MARK  
0  ON  THE  SCHEMATIC  DIAGRAMS  AND  IN  
THE  PARTS  LIST  ARE  CRITICAL  TO  SAFE  OPERATION.
REPLACE  THESE  COMPONENTS  WITH  SONY  PARTS 
 
WHOSE  PART  NUMBERS  APPEAR  AS  SHOWN  IN  THIS  
MANUAL  OR  IN  SUPPLEMENTS  PUBLISHED  BY  SONY.
ATTENTION  AU  COMPOSANT  AYANT  RAPPORT  
À  LA  SÉCURITÉ!
LES  COMPOSANTS  IDENTIFIÉS  PAR  UNE  MARQUE  
0  SUR  
LES  DIAGRAMMES  SCHÉMATIQUES  ET  LA  LISTE  DES  
PIÈCES  SONT  CRITIQUES  POUR  LA  SÉCURITÉ  DE  FONC-
TIONNEMENT.  NE  REMPLACER  CES  COMPOSANTS  QUE  
PAR  DES  PIÈCES  SONY  DONT  LES  NUMÉROS  SONT  DON-
NÉS  DANS  CE  MANUEL  OU  DANS  LES  SUPPLÉMENTS  
PUBLIÉS  PAR  SONY.
Signal-to-noise ratio (SHAKE-33/55/77)
 
More than 90 dB
Dynamic range (SHAKE-33/55/77)
 
More than 88 dB
Video color system format (SHAKE-44D/66D/88D)
 
NTSC and PAL
Tuner section
FM stereo, FM/AM superheterodyne tuner
Antenna:
 
FM lead antenna
 
AM loop antenna
FM tuner section
Tuning range
 US 
model:
 
87.5 MHz – 108.0 MHz (100 kHz step)
 Other 
models:
 
87.5 MHz – 108.0 MHz (50 kHz step)
AM tuner section
Tuning range
 
AEP, UK, RU model:
 
531 kHz – 1,602 kHz (9 kHz step)
 
AUS, E2, E51, US, MX, AR models:
 
531 kHz – 1,710 kHz (9 kHz step)
 
530 kHz – 1,710 kHz (10 kHz step)
 Other 
models:
 
531 kHz – 1,602 kHz (9 kHz step)
 
530 kHz – 1,610 kHz (10 kHz step)
Bluetooth section
Communication system
 
Bluetooth Standard version 3.1
Output
 
Bluetooth Standard Power Class 2
Maximum communication range
 
Line of sight approx. 10m
1)
Frequency band
 
2.4 GHz band (2.4000 GHz – 2.4835 GHz)
Modulation method
 
FHSS (Freq Hopping Spread Spectrum)
Compatible Bluetooth profiles
2)
 
A2DP (Advanced Audio Distribution
 Profile)
 
AVRCP 1.3 (Audio Video Remote
 Control 
Profile)
 
SPP (Serial Port Profile)
Supported codecs
 
SBC (Sub Band Codec)
 
AAC (Advanced Audio Coding)
1)
 The actual range will vary depending on 
factors such as obstacles between devices, 
magnetic fields around a microwave oven, 
static electricity, reception sensitivity, 
antenna’s performance, operating system, soft-
ware application, etc.
2)
  Bluetooth standard profiles indicate the 
purpose of Bluetooth 
communication 
between devices.
General
Power requirements 
 US 
model:
 
AC 120 V, 60 Hz
 MX 
model:
 
AC 120 V – 240 V, 60 Hz
 
AEP, UK, RU model:
 
AC 220 V – 240 V, 50/60 Hz
 E51 
model:
 
AC 220 V – 240 V, 50 Hz
 Other 
models:
 
AC 120 V – 240 V, 50/60 Hz
Power consumption
 SHAKE-77/88D: 
525 
W
 SHAKE-55/66D: 
500 
W
 SHAKE-33/44D: 
350 
W
Power consumption (at the Power Saving mode)
 
 0.5 W (When “BT STANDBY” is set to 
“STANDBY OFF”)
 
 4 W (When “BT STANDBY” is set to 
“STANDBY ON”)
Dimensions (w/h/d) (excl. speakers)
(Approx.)
 
505 mm × 160 mm × 350 mm
 
(20 in × 6 
3
8
 in × 13 
7
8
 in)
Mass (excl. speakers) (Approx.)
 
SHAKE-55/66D/77/88D: 7.6 kg
 
(16 lb 13 oz)
 
SHAKE-33/44D: 7.0 kg (15 lb 7 oz)
Supplied accessories
 
Remote control (1)
 
R6 (Size AA) batteries (2)
 
FM lead/AM loop antenna (1)
 
Bottom panel (1)
Design and specifications are subject to change 
without notice.
License and Trademark Notice
•  
 is a trademark of DVD Format/Logo 
Licensing Corporation.
• 
 
“DVD+RW”, “DVD-RW”, “DVD+R”, 
“DVD-R”, “DVD VIDEO”, and the “CD” logos 
are trademarks.
•   
MPEG Layer-3 audio coding technology and 
patents licensed from Fraunhofer IIS and 
Thomson.
•   Windows Media is either a registered trademark 
or trademark of Microsoft Corporation in the 
United States and/or other countries.
•   This product is protected by certain intellectual 
property rights of Microsoft Corporation. Use 
or distribution of such technology outside of 
this product is prohibited without a license from 
Microsoft or an authorized Microsoft subsidiary.
•   
“WALKMAN” and “WALKMAN” logo are 
registered trademarks of Sony Corporation.
•  This system incorporates Dolby* Digital.
 
Manufactured under license from Dolby 
Laboratories. Dolby and the double-D symbol 
are trademarks of Dolby Laboratories.
•  
The Bluetooth
®
 word mark and logos are 
registered trademarks owned by Bluetooth 
SIG, Inc. and any use of such marks by Sony 
Corporation is under license. Other trademarks 
and trade names are those of their respective 
owners.
•   
The N Mark is a trademark or registered 
trademark of NFC Forum, Inc. in the United 
States and in other countries.
•  Android™ is a trademark of Google Inc.
•  Google Play™ is a trademark of Google Inc.
•   iPhone and iPod touch are trademarks of Apple 
Inc., registered in the U.S. and other countries. 
App Store is a service mark of Apple Inc.
•   “Made for iPod” and “Made for iPhone” mean 
that an electronic accessory has been designed 
to connect specifi 
cally to iPod or iPhone, 
respectively, and has been certifi ed by the 
developer to meet Apple performance standards. 
Apple is not responsible for the operation of 
this device or its compliance with safety and 
regulatory standards. Please note that the use of 
this accessory with iPod or iPhone may affect 
wireless performance.
•   
THIS PRODUCT IS LICENSED UNDER 
THE MPEG-4 VISUAL PATENT PORTFOLIO 
LICENSE FOR THE PERSONAL AND NON-
COMMERCIAL USE OF A CONSUMER FOR
  (i)  
ENCODING VIDEO IN COMPLIANCE 
WITH THE MPEG-4 VISUAL 
STANDARD (“MPEG-4 VIDEO”)
 AND/OR
  (ii) 
 
DECODING MPEG-4 VIDEO THAT 
WAS ENCODED BY A CONSUMER 
ENGAGED IN A PERSONAL AND 
NON-COMMERCIAL ACTIVITY AND/
OR WAS OBTAINED FROM A VIDEO 
PROVIDER LICENSED TO PROVIDE 
MPEG-4 VIDEO.
   
NO LICENSE IS GRANTED OR SHALL 
BE IMPLIED FOR ANY OTHER USE. 
ADDITIONAL INFORMATION INCLUDING 
THAT RELATING TO PROMOTIONAL, 
INTERNAL AND COMMERCIAL USES AND 
LICENSING MAY BE OBTAINED FROM 
MPEG LA, L.L.C.
 HTTP://WWW.MPEGLA.COM
•   All other trademarks and registered trademarks 
are of their respective holders. In this manual, ™ 
and 
®
 marks are not specifi ed.
• Abbreviation
 AR : 
Argentina 
model
 AUS 
Australian 
model
 
E2 
: 120 V AC area in E model
 E4  : 
African 
model
 
E12  : 220-240 V AC area in E model
 
E51  : Chilean and Peruvian models
 
EA 
: Saudi Arabia model
 
MX 
: Mexican model
 
MY 
: Malaysia model
 
RU 
: Russian model
 
SAF  : South African model
 TH : 
Thai 
model
Ver. 1.2
Page of 126
Display

Click on the first or last page to see other HCD-SHAKE33 / HCD-SHAKE44 / HCD-SHAKE55 / HCD-SHAKE66 / HCD-SHAKE77 / HCD-SHAKE88 service manuals if exist.