Read Sony HCD-S500HDE / NAS-SC500PK / SS-S500HDE Service Manual online
HCD-S500HDE/SS-S500HDE
4
SECTION 1
SERVICING NOTES
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
static break-down because of the potential difference generated by
the charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The fl exible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
The laser beam on this model is concentrated so as to be focused
on the disc refl ective surface by the objective lens in the optical
pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTE THE IC501, IC1001, IC1002, IC2001, IC2101,
IC3002, IC9101, IC9201, IC9301 AND IC9401 ON THE
MOTHER BOARD REPLACING
IC501, IC1001, IC1002, IC2001, IC2101, IC3002, IC9101,
IC9201, IC9301 and IC9401 on the MOTHER board cannot ex-
change with single. When these parts are damaged, exchange the
entire mounted board.
IC3002, IC9101, IC9201, IC9301 AND IC9401 ON THE
MOTHER BOARD REPLACING
IC501, IC1001, IC1002, IC2001, IC2101, IC3002, IC9101,
IC9201, IC9301 and IC9401 on the MOTHER board cannot ex-
change with single. When these parts are damaged, exchange the
entire mounted board.
System requirements
System requirements of a computer for using the “Music Transfer” software
Computer
IBM PC/AT compatible
CPU: Pentium III 800 MHz or higher
CPU: Pentium III 800 MHz or higher
RAM: 512 MB or more
Available hard disk drive space: 200 MB or more (1.5 GB or more is
recommended.)
(Depending on the versions of the Windows, the larger amount of
space may be needed.)
(Depending on the versions of the Windows, the larger amount of
space may be needed.)
CD-ROM drive
Sound card
LAN connectors
Operating System*
1
The following manufacturer installed versions only:
Windows XP Service Pack 3
Windows XP Service Pack 3
Windows Vista Service Pack 1
Display
16 bit or better, 800 × 600 dot or more
*
1
The “Music Transfer” software does not support 64-bit Operating Systems.
*
1
Operating systems other than those indicated above are not supported.
System requirements of a computer to connect to the “GIGA JUKE” Wireless
Player
Player
Computer
IBM PC/AT compatible
CPU: 1.00 GHz or higher
Available hard disk drive space: 1.2 GB or more
(The amount of space varies according to the amount of music data
stored on the computer.)
stored on the computer.)
RAM: 256 MB or more
Sound card
Operating System
The following manufacturer installed versions only:
Windows XP Service Pack 3
Windows XP Service Pack 3
Windows Vista Service Pack 1
Software
Server:
VAIO Media Integrated Server Ver. 6.1
VAIO Media Integrated Server Ver. 6.1
VAIO Media Content Collection Ver. 6.0
VAIO Media plus Ver. 1.1/Ver. 1.2
Windows Media Player 11
Notes
We do not ensure trouble-free operation on all computers that satisfy the system requirements.
The NTFS format of Windows XP can be used only with the original manufacturer installed version.
We do not ensure trouble-free operation of the system suspend, system standby, or system hibernation function on all
The NTFS format of Windows XP can be used only with the original manufacturer installed version.
We do not ensure trouble-free operation of the system suspend, system standby, or system hibernation function on all
computers.
We do not ensure trouble-free operation on all computers that satisfy the system requirements. Home-built computers,
upgrade of the original manufacturer-installed operating system, multi-boot environment, multi-monitor environment,
and Macintosh computers are not supported.
and Macintosh computers are not supported.
Depending on the performance of your computer or operating environment, the software may work with some
limitations.
For the latest information about VAIO Media Integrated Server, refer to http://www.vaio-link.com/.
For the latest information about Windows Media Player, visit the Microsoft Corporation website.
For the latest information about Windows Media Player, visit the Microsoft Corporation website.
Click on the first or last page to see other HCD-S500HDE / NAS-SC500PK / SS-S500HDE service manuals if exist.