Read Sony CX-JD33 / CX-JD55 / JAX-D33 / JAX-D55 Service Manual online
24
CX-JD33/JD55
2. DRIVE MANUAL OPERATION
Note:
This mode is used for design, and not used in service fundamental-
ly.
ly.
On the Test Mode Menu screen, press the [2] key on the remote
commander, and the Operation Menu will be displayed. For the
manual operation, each servo on/off control and adjustment can be
executed manually.
commander, and the Operation Menu will be displayed. For the
manual operation, each servo on/off control and adjustment can be
executed manually.
In using the manual operation menu, take care of the following
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.
points. These commands do not provide protection, thus requiring
correct operation. The sector address or time code field is displayed
when a disc is loaded.
Basic operation:
(controllable from front panel or remote commander)
?/1
?/1
: Power OFF (release the Test Mode)
Z
: Stop and eject/Loading
[RETURN]
: Return to Operation Menu or Test Mode Menu
. , >
: Transition between sub modes of menu
[1] to [9], [10/0]
: Selection of menu items
Cursor o / O
: Increase/Decrease in manually adjusted value
2-1. Disc Type
2-1-1. Disc Type Auto Check
1) Press the [1] key on the remote commander to display the Disc
Type Auto Check screen.
2) Insert a disc and press the [ENTER] key on the remote
commander.
3) It judges the type of inserted disc automatically and displays
the disc type and so on as below.
Disc Type
: CD or DVD
Layer
: SINGLE or DUAL
Mirr Time
: Mirror time of between disc surface and record
surface when disc type judgment. (hexadecimal
number)
surface when disc type judgment. (hexadecimal
number)
Mirr Count
: The number of times which mirror counts
between disc surface and record surface when
disc type judging.
between disc surface and record surface when
disc type judging.
FZC Count
: The number of times which focus zero cross
points of each layer when lens down.
points of each layer when lens down.
PI Reference
: The average of PI reference voltage. (hexadeci-
mal number)
mal number)
PI Peak
: PI peak level voltage. It performs only when
disc type judgment is successful. (hexadecimal
number)
disc type judgment is successful. (hexadecimal
number)
2-1-2. Disc Type DVD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.
disc with which the set was inserted.
[1]: DVD single layer disc (12 cm)
[2]: DVD dual layer disc (0 layer, 12 cm)
[3]: DVD dual layer disc (1 layer, 12 cm)
[4]: DVD-RW disc (12 cm)
[5]: DVD single layer disc (8 cm)
[6]: DVD dual layer disc (0 layer, 8 cm)
[7]: DVD dual layer disc (1 layer, 8 cm)
[8]: DVD-RW disc (8 cm)
[2]: DVD dual layer disc (0 layer, 12 cm)
[3]: DVD dual layer disc (1 layer, 12 cm)
[4]: DVD-RW disc (12 cm)
[5]: DVD single layer disc (8 cm)
[6]: DVD dual layer disc (0 layer, 8 cm)
[7]: DVD dual layer disc (1 layer, 8 cm)
[8]: DVD-RW disc (8 cm)
Disc Type
Disc Type Select
1. Disc Type Auto Check
2. Set Disc Type DVD
3. Set Disc Type CD
4. Set Disc Type Hybrid
Exit: RETURN
Disc Type Auto Check
Disc Type
xx
Layer xx
Mirr Time
xx
Mirr Count
xx
FZC Count
xx
PI Reference xx
PI Peak
xx
ENTER.Execute
Exit: RETURN
## Drive Manual Operation ##
Operation Menu
1. Disc Type
2. Servo Control
3. Track/Layer Jump
4. Non EEPROM Write Adjust
5. EEPROM Write Adjust
6. Memory Check
7. Disc Check Memory
8. Error Rate Display
9. SACD Water Mark
Exit: RETURN
Note:
1. Set correctly the disc type to be used on the Disc Type screen.
2. In case of an alarm, exit the manual operation menu immediately to
stop the servo operation, and press the [POWER] button to turn the
power off.
2. In case of an alarm, exit the manual operation menu immediately to
stop the servo operation, and press the [POWER] button to turn the
power off.
Click on the first or last page to see other CX-JD33 / CX-JD55 / JAX-D33 / JAX-D55 service manuals if exist.