Read Sharp TU-X1E (serv.man8) Service Manual online
TU-X1E/RU
7 – 16
[3] TERMINAL UNIT
1. VHIMM1783CQ-1Q
Pin No.
Pin Name
I/O
Pin Function
1
S1_1
I
S Terminal discrimination connection detection
7
S1_2
I
The discrimination result is outputted to a Status register.
13
S1_3
I
19
S1_4
I
2
Y1
I
Luminance signal input Y1
8
Y2
I
Luminance signal input Y2
14
Y3
I
Luminance signal input Y3
20
Y4
I
Luminance signal input Y4
3
S2_1/FS1
I
S Terminal discrimination aspect ratio information input or SCART terminal FS discrimination
9
S2_2/FS2
I
When using it as FS discrimination, it attenats by the resistance division of 47K+33K.
15
S2_3/FS3
I
21
S2_4/FS4
I
4
C1
I
Chroma signal input C1
10
C2
I
Chroma signal input C2
16
C3
I
Chroma signal input C3
22
C4
I
Chroma signal input C4
5
O1
I
General-purpose output
17
O2
I
It is an open collector type general-purpose output port of the I2C control.
23
O3
I
29
O4
I
6
V2
I
Composite signal input V2
12
V3
I
Composite signal input V3
18
V4
I
Composite signal input V4
24
V5
I
Composite signal input V5
26
V6
I
Composite signal input V6
28
V7
I
Composite signal input V7
100
V1
I
Composite signal input V1
33
VCC9
-
Power-supply voltage 9V
61
72
27
72
27
VCC5
-
Power-supply voltage 9V
66
99
25
99
25
GND
-
Ground
30
40
64
68
80
40
64
68
80
11
BIAS
-
Bias
All the reference voltages used in IC are made based on the resistance division of this terminal.
It is a terminal that puts up the filter capacitor outside for the reference voltage stabilization.
All the reference voltages used in IC are made based on the resistance division of this terminal.
It is a terminal that puts up the filter capacitor outside for the reference voltage stabilization.
76
ADR
I
Slave address setting
Slave address 90H and 92H can be selected according to the voltage applied to this terminal.
It is set to 90H by Low, and is set to 92H by High.
Slave address 90H and 92H can be selected according to the voltage applied to this terminal.
It is set to 90H by Low, and is set to 92H by High.
31
SCL
I
I2C BUS clock input
32
SDA
I/O
I2C BUS data input/output
41-60
L1-L10
R1-R10
R1-R10
I
Audio line input
It equips it with ten systems.
It equips it with ten systems.
34-39
LOUT1-3
ROUT1-3
ROUT1-3
O
Audio line output
0dB/6dB of the voltage gain is selected by the control register.
0dB/6dB of the voltage gain is selected by the control register.
62
DCOUT
O
DC output terminal for S terminal
65
VOUT3
O
Monitor output terminal (composite)
63
COUT3/
VOUT6
VOUT6
O
Monitor output terminal (Chroma or composite)
67
VOUT3/
VOUT5
VOUT5
O
Monitor output terminal (Luminance or composite)
69
PROUT2
O
Color difference Pr signal output terminal 2
70
PBOUT2/
COUT2
COUT2
O
Color difference Pb signal output terminal 2
Click on the first or last page to see other TU-X1E (serv.man8) service manuals if exist.