Read Sharp MX-RB14 (serv.man3) Service Manual online
MX-7040N MX-RB14 (PAPER PASS UNIT) 7 – 1
MX-7040N
Service Manual
[7] MX-RB14 (PAPER PASS UNIT)
1. Unpacking
A. Packed items check
2. Installation
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
A. Install the dummy unit
1)
Open the right door of main unit.
2)
Remove the screws and remove the ADU cabinet F lower.
3)
Remove the screw and remove the ADU cabinet R lower.
No.
Name
Quantity
1
Dummy unit
1
2
Upper door
1
3
Front door
1
4
Upper door stopper L
1
5
Upper door stopper R
1
6
ADU cabinet F lower
1
7
ADU cabinet R lower
1
8
Connecting plate lower F
1
9
Connecting plate lower R
1
10
Height adjustment plate
2
11
Step screw
2
12
Screw (P-tight, M4 x 10)
2
13
Screw (S-tight, M4 x 8)
9
14
Step screw
2
15
Washer large
2
16
Washer small
2
17
Spring
1
4
5
6
7
8
9
10
11
13
14
15
16
17
12
1
2
3
2
1
1
1
MX-7040N MX-RB14 (PAPER PASS UNIT) 7 – 2
4)
Install the dummy unit (Packed items No.1) and fix it with the
screws (Packed items No.13).
screws (Packed items No.13).
5)
Fix the ADU cabinet R lower (Packed items No.7) with the
screw (Packed items No.12).
screw (Packed items No.12).
6)
Fix the ADU cabinet F lower with the screws.
B. Install the connection plate
1)
Remove the LCC cabinet.
2)
Install the LCC cabinet with turning over it.
3)
Remove the screws and remove the covers.
Install the connecting plate lower F (Packed items No.8), con-
necting plate lower R (Packed items No.9) and fix it with a
screws (Packed items No.13).
Install the connecting plate lower F (Packed items No.8), con-
necting plate lower R (Packed items No.9) and fix it with a
screws (Packed items No.13).
NOTE: Remove the front and rear covers, then remove the
screws (in the rear side only) as shown in the figure
below. (The removed screws are not used.)
below. (The removed screws are not used.)
1
2
2
2
MX-7040N MX-RB14 (PAPER PASS UNIT) 7 – 3
C. Fix the upper door stopper L
1)
Pierce the concave position on the front cabinet of the right
door.
door.
NOTE: When opening a hole, clean and remove cutting scrap.
2)
Fix the upper door stopper L (Packed items No.4) with the
screws (Packed items No.11).
screws (Packed items No.11).
D. Paper pass unit connection
1)
Lift the left side of the paper pass unit.
2)
Hook the fixing plate of the paper pass unit on the connection
plates of main unit, and lift and push the paper pass unit to
connect the main unit.
plates of main unit, and lift and push the paper pass unit to
connect the main unit.
Procedures to separate from the machine
1)
1)
Insert screwdriver into the hole in the transport section to
release lock of the connection plate.
release lock of the connection plate.
2)
Lift the left side, and release locks of the front and the rear of
the connection plate.
the connection plate.
MX-7040N MX-RB14 (PAPER PASS UNIT) 7 – 4
E. Height adjustment of the paper pass unit
1)
Underlay the adjustment bolt with the adjuster. (two positions)
MEMO: Right side only.
MEMO: Right side only.
2)
Screw the adjustment bolt to adjust the height of the paper
pass unit.
Adjust the edge of the unit below the dotted line.
pass unit.
Adjust the edge of the unit below the dotted line.
3)
Adjust so that the clearance shown below is even.
F. Connector connection
1)
Remove the screw of the upper connector cover and remove
the cover from the main unit.
the cover from the main unit.
2)
Connect the connector and tighten the screw.
G. Fix the front door
1)
Fix the front door (Packed items No.3) with the screws
(Packed items No.12).
(Packed items No.12).
