Read Sharp MX-M654N / MX-M754N (serv.man4) Service Manual online
MX-M754N MX-M654N/M754N (MAIN UNIT) 1 – 5
G. Toner density reference control level setting
1) Connect the power cord of the main unit to the power
outlet.
2) Open the right door unit.
3) Open the front cover, and turn ON the main power switch.
4) Turn ON the power switch on the operation panel.
5) To confirm NOT to put the toner cartridge. Then enter the input
3) Open the front cover, and turn ON the main power switch.
4) Turn ON the power switch on the operation panel.
5) To confirm NOT to put the toner cartridge. Then enter the input
of SIM25-2.
6) After entering the simulation, close the right door unit.
7) Press [EXECUTE] button, and the simulation is executed.
After stirring toner, the toner density control sensor values are
sampled to get the average value of the sensor detection level,
which is set (saved) as the reference toner density control
value. (Takes about 3 minutes or longer depends on environ-
ment condition)
sampled to get the average value of the sensor detection level,
which is set (saved) as the reference toner density control
value. (Takes about 3 minutes or longer depends on environ-
ment condition)
8) After completion of the reference toner density control value
setting, [EXECUTE] key returns to the normal display, showing
completion of the setting operation.
completion of the setting operation.
H. Toner cartridge installation
1) Open the front cover.
2) Install the toner cartridge then close the front cover.
I. Tray setup
(1) System setting
1)
Touch the [Paper Tray Settings] key.
2)
Touch the [Paper Tray Settings] key to configure the settings.
These settings specify the paper type, paper size, and func-
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.
These settings specify the paper type, paper size, and func-
tions allowed for each paper tray. When the [Tray Settings] key
is touched, a list appears showing the trays and the current
settings.
3)
Touch the [Change] key in the above screen to change the set-
tings. The following settings can be configured.
tings. The following settings can be configured.
(2) Tray size setup
a. Inch series tray 1, tray 2 (LT to A4)
1)
1)
Open the tandem paper feed tray.
2)
Push down the paper feed base plate gently, hold the hooks
and remove A4 size regulation plate.
and remove A4 size regulation plate.
Item
Description
Type
Select the type of paper that is loaded in the tray.
The paper types that can be selected vary by paper
tray.
The paper types that can be selected vary by paper
tray.
Size
Select the paper size from the list. The paper sizes
that can be selected vary by tray. The sizes that
can be selected may also be restricted by the paper
type selected above.
If the desired size does not appear in the list, select
[Custom Size] and directly enter the size (only for
the bypass tray).
that can be selected vary by tray. The sizes that
can be selected may also be restricted by the paper
type selected above.
If the desired size does not appear in the list, select
[Custom Size] and directly enter the size (only for
the bypass tray).
Feeding Approved
Job
Job
Select the modes that can be used. If there is a
function that you do not wish to be used with the
selected tray, disable the function. When the "Type"
is other than plain paper, recycled paper, colored
paper, or a user type, [Fax] and [Internet Fax]
cannot be selected.
function that you do not wish to be used with the
selected tray, disable the function. When the "Type"
is other than plain paper, recycled paper, colored
paper, or a user type, [Fax] and [Internet Fax]
cannot be selected.
1
1
3
3
3
3
2
2
Click on the first or last page to see other MX-M654N / MX-M754N (serv.man4) service manuals if exist.