MX-M364N, MX-565N (serv.man4). Service Manual (Revised January 2016). - Sharp Copying Equipment Service Manual (repair manual). Page 3

Read Sharp MX-M364N / MX-565N (serv.man4) Service Manual online

MX-M565N NOTE FOR SERVICING - i
MX-M503N
Service Manual
 
NOTE FOR SERVICING
1.
Precautions for servicing
1)
When servicing, disconnect the power plug, the printer cable,
the network cable, and the telephone line from the machine,
except when performing the communication test, etc.
It may cause an injury or an electric shock.
2)
There is a high temperature area inside the machine. Use an
extreme care when servicing.
It may cause a burn.
3)
There is a high voltage section inside the machine which may
cause an electric shock. Be careful when servicing.
4)
Do not disassemble the laser unit. Do not insert a reflective
material such as a screwdriver in the laser beam path.
It may damage eyes by reflection of laser beams.
5)
When servicing with the machine operating, be careful not to
squeeze you hands by the chain, the belt, the gear, and other
driving sections.
6)
Do not leave the machine with the cabinet disassembled.
Do not allow any person other than a serviceman to touch
inside the machine. It may cause an electric shock, a burn, or
an injury.
7)
When servicing, do not breathe toner, developer, and ink
excessively. Do not get them in the eyes.
If toner, developer, or ink enters your eyes, wash it away with
water immediately, and consult a doctor if necessary.
8)
The machine has got sharp edges inside. Be careful not to
damage fingers when servicing.
9)
Do not throw toner or a toner cartridge in a fire. Otherwise,
toner may explode and burn you.
10) When replacing the lithium battery on the PWB, used the spec-
ified battery only.
If a battery of different specification is used, the battery may
cause malfunction or breakdown of the machine.
11) When carrying a unit with PWB or electronic parts installed on
it, be sure to put it in an anti-static-electricity bag.
It may cause a breakdown or malfunctions.
2.
Warning for servicing
1)
Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Avoid complex wiring, which may lead to a fire or an electric
shock.
It may cause a fire or an electric shock.
2)
If there is any abnormality such as smoke or an abnormal
smell, interrupt the job and disconnect the power plug.
It may cause a fire or an electric shock.
3)
Be sure to connect the grounding wire. If an electric leakage
occurs without grounding, a fire or an electric shock may
result.
To protect the machine and the power unit from lightening,
grounding must be made.
4)
When connecting the grounding wire, never connect it to the
following points.
It may cause an explosion, a fire or an electric shock.
* Gas tube
* Lightning conductor
* A water pipe or a water faucet, which is not recognized as a
grounding object by the authorities.
* Grounding wire for telephone line
5)
Do not damage, break, or stress the power cord.
Do not put heavy objects on the power cable. Do not forcibly
bend, pull, or strain the power cord.
It may cause a fire or an electric shock.
6)
Keep the power cable away from a heat source.
Do not insert the power plug with dust on it into a power outlet.
It may cause a fire or an electric shock.
7)
Do not put a metallic object or a container with water in it inside
the machine.
It may cause a fire or an electric shock.
8)
Do not perform servicing, touch the power plug, insert a tele-
phone jack, or operate the machine with wet or only hands.
3.
Note for installing site
Do not install the machine at the following sites.
1)
Place of high temperature, high humidity, low tempera-
ture, low humidity, place under an extreme change in tem-
perature and humidity.
Paper may get damp and form moisture inside the machine,
causing paper jam or copy dirt.
For operating and storing conditions, refer to the specifications
described future in the Service Manual.
2)
Place of much vibration
It may cause a breakdown.
3)
Poorly ventilated place
An electrostatic type copier will produce ozone inside it.
The quantity of ozone produced is designed to a low level so
as not to affect human bodies. However, continuous use of
such a machine may produce an odor of ozone. Install the
machine in a well ventilated place strike, and ventilate occa-
sionally.
CAUTION
DOUBLE POLE/NEUTRAL FUSING
(200V series only)
Page of 127
Display

Click on the first or last page to see other MX-M364N / MX-565N (serv.man4) service manuals if exist.