MX-M350N, MX-M350U, MX-M450N, MX-M450U (serv.man21). Administrator Settings Guide - Sharp Copying Equipment User Guide / Operation Manual. Page 13

This setting is used to disable the function that changes
the key display order each time a selected tab is
touched on a screen that is divided into tabs, including
the screens for selecting the user name and folder for
the "SCAN TO HDD" and "FILE" functions, and the
address book screen of image send mode.
This does not affect the function that changes the order
of display of files in document filing folders.

This setting is used to prohibit changes to the clock
adjust setting. When this setting is enabled, "Clock" in
the system settings cannot be used. To adjust the date
and time, this setting must first be disabled (remove the
checkmark).

Use these settings when a peripheral device on the
machine has failed or when you wish to temporarily
disable a device. These settings can also be used to
change certain device function settings as needed to
suit the needs of your workplace.
"Device control" consists of the following settings:

● Original size detector setting
● Disabling of document feeder
● Disabling of duplex
● Disabling of stapler
● Disabling of punch
● Disabling of optional paper drawer
● Disabling of finisher
● Disabling of mail-bin stacker
● Disabling of covers/inserts mode
● Saddle stitch position adjust
● High speed stacking
● Rotated output
● Auto paper selection setting
● Optimization of a hard disk

This setting is used to select the standard original sizes
that are detected by the original size detection function.
Select one of the four groups indicated below. The
factory default setting is "INCH-1 (AB-1)". Original size
detection by the document glass can also be disabled.

If "CANCEL DETECTION AT DOCUMENT GLASS" is
set, originals will be regarded as EXTRA for all copier
functions and no original size will be displayed.

This setting is used to prevent use of the automatic
document feeder when it malfunctions. In this case,
scanning can still be performed using the document
glass.

This setting is used to disable duplex printing when the
duplex module malfunctions. When this settings is
enabled, only one-sided printing can be performed.

This setting is used to disable stapling when the stapler
unit of the finisher or the saddle stitch finisher
malfunctions.

Use this setting when you wish to prohibit punching or
when the punch unit of the finisher or saddle stitch
finisher has failed.

This setting is used to disable use of the stand/3 x 500
sheet paper drawer or stand/MPD & 2000 sheet paper
drawer when it malfunctions.

Use this setting when you wish to prohibit use of the
finisher or saddle stitch finisher, or when either has
failed.

This setting is used to disable use of the mail-bin
stacker when it malfunctions.

Use this setting to prohibit the use of covers/inserts
mode.

Group

Detectable original sizes

Document feeder tray (for automatic
document feeder)

Document glass

1 INCH-1

11" x 17", 8-1/2" x 14",
8-1/2" x 11", 
8-1/2" x 11"R,
5-1/2" x 8-1/2"

A3, A4

2 INCH-2

11" x 17", 8-1/2" x 13",
8-1/2" x 11", 
8-1/2" x 11"R,
5-1/2" x 8-1/2"

A3, A4

3 AB-1

A3, A4, A4R, A5,
B4, B5, B5R

11" x 17", 8-1/2"
x 11",
216x330

4 AB-2

A3, A4, A4R, A5,
B5, B5R, 216x330

11" x 17", 8-1/2"
x 11", B4

JupiterII_Admin_ex.book  11 ページ  ２００６年１２月４日　月曜日　午後１時３６分