Read Sharp MX-M266N / MX-M316N / MX-M356N (serv.man3) Service Manual online
MX-M356NV SIMULATION 6 – 24
26-3
Purpose
Setting
Function (Purpose) Used to set the specifications of the auditor.
(Setting must be made according to the
auditor use conditions.)
auditor use conditions.)
Section
Auditor
Operation/Procedure
Select an item to be set with the touch panel.
Select an item to be set with the touch panel.
(*1) Displayed only when EQUITRAC.
(*2) Details of the vendor mode
(*2) Details of the vendor mode
Details of the vendor mode
Operation 1:
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2:
Auto clear is not made.
Operation 3:
The display is shifted to the initial screen.
Standby during setting time of auto clear. Default is 60 seconds,
which can be changed in the system setting.
Operation 2:
Auto clear is not made.
Operation 3:
The display is shifted to the initial screen.
Destination
Setting value
LEGAL SET
G/LBS SET
U.S.A
8.5 x 14
LBS
CANADA
8.5 x 14
LBS
INCH
8.5 x 14
LBS
JAPAN
8.5 x 14
GRAM
AB_B
8.5 x 14
GRAM
EUROPE
8.5 x 14
GRAM
U.K.
8.5 x 14
GRAM
AUS.
8.5 x 14
GRAM
AB_A
8.5 x 14
GRAM
CHINA
8.5 x 14
GRAM
Item/Display
Content
Default
value
BUILT-IN
AUDITOR
AUDITOR
P10
Built-in auditor mode
(standard mode) operation.
(standard mode) operation.
P10
OUTSIDE
AUDITOR
AUDITOR
NONE
No external connection
vendor is used.
vendor is used.
NONE
P VENDOR1
Coin vendor mode
(Only the copy mode can
be controlled.)
(Only the copy mode can
be controlled.)
P VENDOR3
Vendor mode in which
signals for the intercard
connected to the PCU are
used for communication in
parallel I/F.
signals for the intercard
connected to the PCU are
used for communication in
parallel I/F.
P OTHER
Mode for an external
auditor connected to the
SCU.
auditor connected to the
SCU.
VENDOR-EX
(*1)
(*1)
Vendor I/F for EQUITRAC
VENDOR-EX
(MULTI) (*1)
(MULTI) (*1)
VENDOR-EX + Multi job
cueing Enable mode
cueing Enable mode
S_VENDOR
Serial vendor mode
DOC ADJ
ON
Support for the auditor in
document filing print
document filing print
OFF
OFF
No support for the auditor in
document filing print
document filing print
PF ADJ
ON
Continuous printing is
performed in the duplex
print mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
performed in the duplex
print mode.
If the remaining money
expires during continuous
printing, the sheets in the
machine are discharged
without being printed on the
back surfaces.
OFF
OFF
Continuous printing is not
performed in the duplex
print mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back
surface.
performed in the duplex
print mode. (The remaining
amount is checked for
printing every surface in all
the printing process.)
If the remaining money
expires during printing, the
sheet is discharged without
printing on the back
surface.
VENDOR
MODE (*2)
MODE (*2)
MODE1
Vendor mode 1
MODE
3
MODE2
Vendor mode 2
MODE3
Vendor mode 3
COUNTUP
TIMING
TIMING
FUSER_IN
Mode in which the detection
timing of the paper lead
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
timing of the paper lead
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
EXIT_
OUT
FUSER_OUT
Mode in which the detection
timing of the paper rear
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
timing of the paper rear
edge by the sensor after the
paper passes the fusing
section is used as the
money charging timing.
EXIT_OUT
Mode in which the detection
timing of the paper rear
edge by the paper exit
sensor of the right paper
exit tray or of the after
process unit is used as the
money charging timing.
timing of the paper rear
edge by the paper exit
sensor of the right paper
exit tray or of the after
process unit is used as the
money charging timing.
PRINTER
CONTROL
CONTROL
MODE1
All the items in OUTSIDE
AUDITOR and VENDOR
MODE are allowed to
select.
AUDITOR and VENDOR
MODE are allowed to
select.
MODE
1
MODE2
(“OUTSIDE AUDITOR” is
always set to “P
VENDOR1”. Other buttons
are grayed out.
“VENDOR MODE” is
always set to “MODE3”.
Other buttons are grayed
out.)
always set to “P
VENDOR1”. Other buttons
are grayed out.
“VENDOR MODE” is
always set to “MODE3”.
Other buttons are grayed
out.)
MODE3
“OUTSIDE AUDITOR” is
always set to “P OTHER”.
Other buttons are grayed
out.
“VENDOR MODE” is
always set to “MODE3”.
Other buttons are grayed
out.
always set to “P OTHER”.
Other buttons are grayed
out.
“VENDOR MODE” is
always set to “MODE3”.
Other buttons are grayed
out.
Completion
of the
specified
quantity.
(Money
remaining)
Insufficient money during
copy job
Completion
of the
specified
quantity.
(No money
remaining)
remaining)
BW
(no money
remaining)
remaining)
BW
(money
remaining)
Condition 1
Condition 2
Condition 3
Condition 4
MODE1
Operation 1
Operation 2
Operation 2
Operation 1
MODE2
Operation 1
Operation 1
Operation 2
Operation 1
MODE3
Operation 1
Operation 3
Operation 2
Operation 3
Item/Display
Content
Default
value
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N (serv.man3) service manuals if exist.