Read Sharp MX-LC13 (serv.man15) Technical Bulletin online
MX-M1204 MX-LC13 (LARGE CAPACITY TRAYS) 8 – 7
Rear side
17) Adjust the height of the exterior cabinet to the same level.
Front side
Rear side
D. Turn ON the power of the main unit
1) Connect the power plug of the machine to the power outlet,
and turn ON the main power switch and the operation panel
power switch.
power switch.
E. Size setting
1) Check to insure that the main body is standby state, and press
the [System setting] key on the operation panel.
2) Menu screen is displayed on the touch panel. Select the
[Paper Tray Settings].
3) Select the paper size of large capacity tray from contents of
[Paper Tray Settings].
F. Off-center adjustment
(1) Off-center check
Since the off-center adjustment has been made at shipping, there
is normally no need to adjust. If, however, the center is shifted,
carry out the following steps to adjust.
1)
is normally no need to adjust. If, however, the center is shifted,
carry out the following steps to adjust.
1)
Run Sim50-10 using the keypad on the main unit.
2)
This screen allows you to configure the print off-center adjust-
ment value for each paper feed tray.
ment value for each paper feed tray.
3)
On the touch panel, press DOWN key to select "H: 50:
MAINLCT1" and press the [EXECUTE] key
MAINLCT1" and press the [EXECUTE] key
4)
Check that the adjustment pattern image is printed in the cor-
rect position.
Measure the dimensions of the void areas on the front and rear
frame sides of the adjustment pattern image, and make sure
that the following conditions are met:
rect position.
Measure the dimensions of the void areas on the front and rear
frame sides of the adjustment pattern image, and make sure
that the following conditions are met:
“A-B” is over 3mm: Move to Mechanical Adjustment 1
“A-B” is less than +/-3mm: Move to Mechanical Adjustment 2
“A-B” is less than +/-3mm: Move to Mechanical Adjustment 2
(2) Mechanical Adjustment
a. Mechanical Adjustment1
When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:
1)
When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:
1)
If the image shifts to the front side, lift up the front side adjuster
in order to correct the paper transport position as a figure
below.
in order to correct the paper transport position as a figure
below.
$
%
3ULQWHGVXUIDFH
3DSHUGHOLYHU\
GLUHFWLRQ
GLUHFWLRQ
,IWKHGLPHQVLRQRI%LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVUHDUGLUHFWLRQ
VKLIWGLUHFWLRQLVUHDUGLUHFWLRQ
,IWKHGLPHQVLRQRI$LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVIURQWGLUHFWLRQ
VKLIWGLUHFWLRQLVIURQWGLUHFWLRQ
5HDU6LGH
)URQW6LGH
$%
PP0HFKDQLFDODGMXVWPHQWPP0HFKDQLFDODGMXVWPHQW
PP0HFKDQLFDODGMXVWPHQWPP0HFKDQLFDODGMXVWPHQW
TopPage
4
: ‘14/Jan
4
Click on the first or last page to see other MX-LC13 (serv.man15) service manuals if exist.