MX-FX11 (serv.man2). Image Send Error Code List - Sharp Copying Equipment Service Manual (repair manual). Page 2

31 

Refer to "previous table". 

Depends on the point of communication interruption. For 16 or later, V.34 mode communication. 

33 

BUSY 

The calling side cannot establish connection with the remote party. 

34 

CANCEL 

A communication interruption command is made during sending/receiving. The interruption key is pressed for 

interruption of input. <Send/Receive/Polling/Bulletin board> 

35 

NG35 XXXX 

Power is failed during sending/receiving. <Send/Receive/Polling/Bulletin board> 

36 

(No record paper) 

37 

(Record paper jam) 

38 

MEM. FULL 

Memory over during reception. <Receive/Polling> 
Print is not made during reception in acting reception inhibit. <Receive/Polling> 

39 

(Number of paper 
unmatched) 

40 

(Relay not received) 

41 

LENGTH OVER 

The send data length of one page exceeds the limit (2m) in sending. <Send/Bulletin board> 

42 

LENGTH OVER 

The receive data length of one page exceeds the limit. <Receive/Polling> 

43 

(Communication) (OK) 

Speaking before data transmission 

44 

ORIGINAL ERROR 

A document jam occurs in direct sending. <Send> 

45 

(Picture quality error) 

46 

NO RESPONSE 

The FAX signal from the remote party is not detected within Ti time. <Send/Polling> 

(When in recall, however, the recall setting in case of a communication error is valid.) 

47 

TX DECODE ERROR 

A decode error occurs in the FAX board. <Send/Bulletin board> 

48 

OK 

Normal end of communication 

OK REPLY RECEIVE 

OK in Internet FAX send with reception confirmation. 

49 

NO RX POLL 

The called side does not have polling function in polling reception. <Polling> 
The called side has no data to send. <Polling> 

50 

RX POLL FAIL 

In polling reception, DCN is received for DTC. <Polling> 
In polling sending, there is no send data. <Bulletin board> 

51 

PASS # NG 

In poling sending, the allow number is not matched. <Bulletin board> 
In polling sending, the system number is not matched. <Bulletin board> 

52 

(No confidential function in 

remote party) 

In confidential sending, the remote party does not have confidential function. <Send> 
(Including other company's machines) 
1)  The NSF signal has not "Confidential function" bit. 

2)  The NSF is not a Sharp machine. 

53 

(Confidential not received) 

1) 

In confidential sending, DCN is received for NSS. <Send> 

54 

(Confidential BOX NO NG)  1 

In confidential reception, a confidential box number which is not registered is specified. 

55 

(No relay function in 

remote party) 

In relay command sending, the remote machine has no relay function. <Send> 
(Including other company's machine) 
1)  The NSF signal has not "Confidential function" bit. 

2)  The NSF is not a Sharp machine. 

56 

NO REL RX 

1)  In relay command sending, DCN is received for NSS. <Send> 

2)  In relay command reception, a remote station number which is not registered is specified. <Receive> 
3)  In F code relay broadcasting, an F code relay command is received.<Receive> 

57 

(Relay ID unmatched) 

In relay command reception, the relay ID does not match. <Receive> 

58 

REJECTED 

In reception, data are sent from a remote machine of receive inhibit number. <Receive> 
(Not rejected in the bulletin board send or the F code bulletin board send.) 

59 

RX NO F-CODE POLL 

In F code polling (calling), the remote machine has no DIS bit 47 (polling function). <Polling> 
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)<Polling> 

60 

NO F-CODE POLL 

In F code polling (calling), DCN is received for SEP. <Polling> 
In bulletin board, there is no send data for SEP. <Bulletin board> 

61 

RX POLL # NG 

In bulletin board, the sub address (bulletin board number (SEP)) is not matched. <Bulletin board> 

62 

F POLL PASS # NG 

In bulleting board, the pass code (PWD) is not matched. <Bulletin board> 

63 

NO F FUNC 

In F code sending, the remote machine has no DIS bit 49 (sub address function). <Send> 

(Check that the remote machine conforms to F code.) 

64 

NO F-CODE 

In F code sending : <Send> 
1)  DCN is received for SUB. --- Check the box number. 

2)  DCN is received for SID. --- Check the box number and pass code. 

In F code receiving : <Receive> 

"F code relay broadcasting" or "F code confidential reception" is "Inhibited with soft SW." 

67 

F PASS # NG 

In F code receiving, the pass code (SID) is not matched. <Receive> 

68 

BOX NO. NG 

In F code reception, a box number which is not registered is specified. (SUB is not matched.) <Receive> 

69 

MEMORY OVER 

Memory over in quick online sending <Send> 

70 

(JOB MEMORY OVER) 

In PC-FAX reservation, the number of remote parties is exceeded. <Send> 

71 

NG71 XXXX *

1 

 

In PC-FAX reservation, data sent from PC includes some errors. <Send> 

72 

(NG72 XXXX) 

 *

1 

 

In department management setting on the machine side: 

•  In reservation from PC-FAX or PC-Internet FAX, a department number which is not registered on the 

machine side is specified. <Send> 

•  In reservation from PC-FAX or PC-Internet FAX, the department number is not specified. <Send> 

73 

NG73 XXXX 

 *

1 

 

In reservation from PC-FAX or PC-Internet FAX, the use quantity limit is exceeded. <Send> 

74 

NG74 XXXX 

 *

1 

 

When reserving specified filing in document filing in PC-FAX or PC-Internet FAX; 
•  The pass-code for the folder is set on the machine side and the pass-code from PC-XXX does not match 

with it. <Send> 

•  The pass-code for the folder is set on the machine side and no pass-code is specified by PC-XXX. <Send> 

MX-FX11 TROUBLE CODE 3 — 2