Read Sharp MX-B201D (serv.man6) Service Manual online
MX-FX12 FAX SOFT SWITCH 2 - 8
S
W
26
1
Read completion
sound
sound
Used to set whether buzzer sound is made or not when scan is
completed.
In manual send or when scan is completed in direct send, buzzer
sound is not made.
completed.
In manual send or when scan is completed in direct send, buzzer
sound is not made.
1sec.
0
1: Mute
0: 1sec.
2
Error beep of FAX
RX in case of the
sender fax is no
response
RX in case of the
sender fax is no
response
Setting of communication error beep when machine arrives as fax
reception, and fax signal is not received from sending side.
reception, and fax signal is not received from sending side.
Communication
error beep is
invalid
0
1: Communication error beep is
effective
effective
0: Communication error beep is
invalid
invalid
3
Speaker volume
setup
setup
Used to set speaker volume.
The following sounds are the targets of this setting.
• Alarm sound
The following sounds are the targets of this setting.
• Alarm sound
• Send end sound
• Receive end sound
• Scan end sound
Small
0
Refer to User program
“BEEPER VOLUME (send
completion sound / receive
completion sound / scan
completion sound / alarm
sound)”
“BEEPER VOLUME (send
completion sound / receive
completion sound / scan
completion sound / alarm
sound)”
4
Bit No.
3
4
1
Silent
0
0
Small
0
1
Medium
1
0
Large
1
1
5
Inhibited to use
0
6
0
7
0
8
0
S
W
27
1
Inhibited to use
0
2
0
3
0
4
0
5
0
6
0
7
Recording paper
tray selection
tray selection
Used to select the recording paper tray used by FAX.
Valid only when two cassettes are installed.
Valid only when two cassettes are installed.
AUTO
0
Refer to User program
“TRAY SELECTION”.
When a value outside the
set range is set, the initial
value is set.
“TRAY SELECTION”.
When a value outside the
set range is set, the initial
value is set.
Bit No.
7
8
8
AUTO
0
0
0
TRAY1
0
1
TRAY2
1
0
S
W
28
1
Inhibited to use
0
2
0
3
0
4
0
5
0
6
0
7
0
8
0
S
W
29
1
Number of auto
switch calls of
manual reception
auto reception
switch calls of
manual reception
auto reception
Used to set the number of calls to switch to auto receive in manual
receive mode.
receive mode.
0 time
0 Refer to User program
“# OF RINGS MANUAL RX”.
When a value outside the
set range is set, the initial
value is set.
When a value outside the
set range is set, the initial
value is set.
2
0
When set to 0, switch to auto receive is not made.
3
Binary input
0
Bit No.
1
2
3
4
4
Set range
0 to 9
0
Not switched when 0.
5
Setup of number
of times of call
rings
of times of call
rings
Used to set the number of calls before starting reception in auto
receive mode.
receive mode.
2 times
0 Refer to User program
“# OF RINGS AUTO RX”.
When a value outside the
set range is set, the initial
value is set.
When a value outside the
set range is set, the initial
value is set.
6
0
7
Setting is made in binary input.
1
Binary input
8
Bit No.
5
6
7
8
0
Set range
0 to 9 times
SW
NO.
Data
No.
Item
Switch selection and contents of functions
Initial value
Remark
Click on the first or last page to see other MX-B201D (serv.man6) service manuals if exist.