Read Sharp MX-6580N / MX-7580N (serv.man3) Service Manual online
MX-7580N ADJUSTMENTS AND SETTINGS 5 – 65
2)
Check the copy image center position.
If A - B = +/- 1.0mm, the adjustment is not required.
If the above condition is not satisfied, perform the following
procedures.
procedures.
3)
Enter the SIM 50-12 mode.
4)
Select the adjustment mode OC with the scroll key.
5)
Enter the adjustment value with 10-key, and press [OK] key.
The entered value is set.
When the set value is increased, the main scanning print posi-
tion is shifted to the front side by 0.1mm.
tion is shifted to the front side by 0.1mm.
6)
Go to the copy mode, and make a copy.
Repeat the procedures of 1) - 6) until the above condition is satis-
fied.
fied.
15-B
Scan image off-center adjustment
(Manual adjustment) (DSPF mode)
(Manual adjustment) (DSPF mode)
This adjustment must be performed in the following cases:
* When the scan control PWB is replaced.
* When the EEPROM on the scan control PWB is replaced.
* When the scanner (reading) section is disassembled.
* When the scanner (reading) section is replaced.
* When U2 trouble occurs.
* When the DSPF section is disassembled.
* When the DSPF unit is replaced.
CAUTION: To execute this adjustment, it is required that the
ADJ15A Scan image off-center adjustment (Document
table mode) must have been properly adjusted.
table mode) must have been properly adjusted.
1)
Prepare the adjustment chart.
Draw a line at the center of the front surface and the back sur-
face of A4 (11" x 8.5") paper in parallel with the paper transport
direction.
face of A4 (11" x 8.5") paper in parallel with the paper transport
direction.
2)
Set the adjustment chart to the DSPF.
3)
Make a duplex copy in the normal magnification ratio from the
manual paper feed tray, and check the image position on the
front surface and the back surface of the copy paper.
manual paper feed tray, and check the image position on the
front surface and the back surface of the copy paper.
If the difference is within the range of 0 +/- 2.7mmm there is no
need to perform the adjustment.
need to perform the adjustment.
If the adjustment is required, perform the following procedures.
4)
Enter the SIM 50-12 or 50-6 mode.
SIM50-12
A - C: When the adjustment value is increased, the image
position is shifted to the rear frame side.
position is shifted to the rear frame side.
1step = 0.1mm
SIM50-6
B'
A' - B' = 1.0mm
A'
(100%)
Paper transport direction
Front surface
Back surface
Draw a line at the center of the
front surface and the back surface
of paper in parallel with the paper
transport direction.
Item
Display
Content
Setting
range
Default
value
A
OC
Document table image off-
center adjustment
center adjustment
1 - 99
50
B
SPF(SIDE1)
SPF front surface image off-
center adjustment
center adjustment
1 - 99
50
C
SPF(SIDE2)
SPF back surface image off-
center adjustment
center adjustment
1 - 99
50
Item/Display
Content
Setting
range
Default
value
A
SIDE1
Front surface
document scan
position adjustment
(CCD)
document scan
position adjustment
(CCD)
1 - 99
50
B
SIDE2
Back surface
document scan
position adjustment
(CCD)
document scan
position adjustment
(CCD)
1 - 99
50
C
Image loss
amount
setting
SIDE1
amount
setting
SIDE1
LEAD_
EDGE
(SIDE1)
EDGE
(SIDE1)
Front surface lead
edge image loss
amount setting
edge image loss
amount setting
0 - 99
20
D
FRONT_
REAR
(SIDE1)
REAR
(SIDE1)
Front surface side
image loss amount
setting
image loss amount
setting
0 - 99
20
E
TRAIL_
EDGE
(SIDE1)
EDGE
(SIDE1)
Front surface rear
edge image loss
amount setting
edge image loss
amount setting
0 - 99
40
F
Image loss
amount
setting
SIDE2
amount
setting
SIDE2
LEAD_
EDGE
(SIDE2)
EDGE
(SIDE2)
Back surface lead
edge image loss
amount setting
edge image loss
amount setting
0 - 99
40
G
FRONT_
REAR
(SIDE2)
REAR
(SIDE2)
Back surface side
image loss amount
setting
image loss amount
setting
0 - 99
20
H
TRAIL_
EDGE
(SIDE2)
EDGE
(SIDE2)
Back surface rear edge
image loss amount
setting
image loss amount
setting
0 - 99
20
I
OFFSET_SPF1
DSPF front surface
document off-center
adjustment
document off-center
adjustment
1 - 99
50
J
OFFSET_SPF2
DSPF back surface
document off-center
adjustment
document off-center
adjustment
1 - 99
50
K
SCAN_SPEED_SPF1
DSPF document front
surface magnification
ratio (Sub scan)
surface magnification
ratio (Sub scan)
1 - 99
50
original
copy
a
b
Click on the first or last page to see other MX-6580N / MX-7580N (serv.man3) service manuals if exist.