Read Sharp MX-6240N / MX-7040N (serv.man24) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 84
8)
In the case of paper feed tray 3/4
Loosen the paper feed tray off-center adjustment screws (2
pcs.) at the center section of the lift plate of the paper feed tray,
and change the gear unit position in the front/rear frame direc-
tion. Repeat the adjustment procedures from 4).
pcs.) at the center section of the lift plate of the paper feed tray,
and change the gear unit position in the front/rear frame direc-
tion. Repeat the adjustment procedures from 4).
NOTE:
Normally if the adjustment is executed by ADJ3 (automatic adjust-
ment), there is no need to execute this adjustment.
ment), there is no need to execute this adjustment.
Only when the manual adjustment is required, execute this adjust-
ment.
ment.
In other words, this manual adjustment is executed when a satis-
factory result is not obtained from the automatic adjustment
(ADJ3).
factory result is not obtained from the automatic adjustment
(ADJ3).
The adjustment item (SUB-XXX-HV-XXX) is used to make the fine
adjustment of heavy paper/OHP/envelopes for the adjustment item
(SUB-XXX) of each paper feed tray.
adjustment of heavy paper/OHP/envelopes for the adjustment item
(SUB-XXX) of each paper feed tray.
ADJ 16
Scan image magnification ratio
adjustment
(Manual adjustment)
adjustment
(Manual adjustment)
NOTE:
Normally if the adjustment is executed by ADJ3 (automatic adjust-
ment), there is no need to execute this adjustment.
ment), there is no need to execute this adjustment.
Only when the manual adjustment is required, execute this adjust-
ment.
ment.
In other words, this manual adjustment is executed when a satis-
factory result is not obtained from the automatic adjustment
(ADJ3).
factory result is not obtained from the automatic adjustment
(ADJ3).
16-A
Scan image magnification ratio adjustment
(main scanning direction) (Manual
adjustment) (Document table mode)
(main scanning direction) (Manual
adjustment) (Document table mode)
CAUTION: If the default adjustment value of the scan image magni-
fication ration adjustment (main scanning direction) of
SIM 48-1, copy image quality may be degraded. There-
fore, this adjustment must be executed only when there
is a special necessity.
SIM 48-1, copy image quality may be degraded. There-
fore, this adjustment must be executed only when there
is a special necessity.
This adjustment must be performed in the following cases:
* When the copy magnification ratio in the copy image main scan-
ning direction is not properly adjusted.
* When the scanner motor is replaced.
* U2 trouble has occurred.
* When the scanner control PWB is replaced.
* When the EEPROM of the scanner control PWB is replaced.
Before this adjustment, the focus adjustment (CCD unit installing
position adjustment) must have been completed.
position adjustment) must have been completed.
1)
Place a scale on the document table as shown in the figure
below.
below.
2)
Enter the SIM 48-1 mode.
ǂǂǂ6,08/$7,21ǂǂ12
7(67
&/26(
˖&&'0$,1
˖&&'68%
˖63)0$,1
˖63)68%
˖63)%0$,1
0$*1,),&$7,21$'-8670(17
$
˷̚˹
$˖
%˖
&˖
'˖
(˖
2.
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
%$&.
0212
&2/25
(;,7
&/($5
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man24) service manuals if exist.