Read Sharp MX-6240N / MX-7040N (serv.man24) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 82
After execution of the above, perform procedures 1) - 4) to
check that the void area is within the specified range.
check that the void area is within the specified range.
Though the lead edge void area adjustment value is proper, if
the lead edge void area is not within the specified range,
change the adjustment value of item (SUB-XXX) in SIM 50-10.
Refer to ADJ15-C.
the lead edge void area is not within the specified range,
change the adjustment value of item (SUB-XXX) in SIM 50-10.
Refer to ADJ15-C.
Repeat the above procedures until a satisfactory result is obtained.
15-C
Print image manual position adjustment
(Main scanning direction, sub scanning
direction) (Print engine) (Each paper feed
tray)
(Main scanning direction, sub scanning
direction) (Print engine) (Each paper feed
tray)
This adjustment must be performed in the following cases:
* When the LSU is replaced or removed.
* When a paper tray is replaced.
* When the paper tray section is disassembled.
* When ADJ15A Print image manual magnification ratio adjust-
ment (Main scanning direction) (Print engine) is performed.
* When the manual feed tray is replaced.
* When the manual feed tray is disassembled.
* When the duplex mode paper transport section is disassembled.
* When the registration roller section is disassembled.
* U2 trouble has occurred.
* The PCU PWB has been replaced.
* The EEPROM of the PCU PWB has been replaced.
NOTE: Before execution of this adjustment, check to insure the fol-
lowing item.
* The print image manual magnification ration adjustment
(ADJ15A) (main scanning direction) (Print engine) has been
properly adjusted.
properly adjusted.
SIM 50-10 display item
Heavy paper A: Heavy paper 1 - 2, Embossed paper, Label sheet,
Tab sheet, Glossy paper
Tab sheet, Glossy paper
Heavy paper B: Heavy paper 3 - 4
Item/Display
Content
Setting
range
Default
value
Print off
center
adjust-
ment
center
adjust-
ment
BK-MAG
Main scan print
magnification ratio
magnification ratio
60 - 140
100
MAIN-MFT
(Print off center) manual
feed adjustment value
feed adjustment value
1 - 99
50
MAIN-CS1
(Print off center) tray 1
adjustment value
adjustment value
1 - 99
50
MAIN-CS2
(Print off center) tray 2
adjustment value
adjustment value
1 - 99
50
MAIN-CS3
(Print off center) tray 3
adjustment value
adjustment value
1 - 99
50
MAIN-CS4
(Print off center) tray 4
adjustment value
adjustment value
1 - 99
50
MAIN-LCC
(Print off center) LCC
adjustment value
adjustment value
1 - 99
50
MAIN-LCT1
Print off center
adjustment value (LCT1)
adjustment value (LCT1)
1 - 99
50
MAIN-LCT2
Print off center
adjustment value (LCT2)
adjustment value (LCT2)
1 - 99
50
MAIN-LCT-
MFT
MFT
Print off center
adjustment value
(LCT_manual feed)
adjustment value
(LCT_manual feed)
1 - 99
50
MAIN-ADU
(Print off center) ADU
adjustment value
adjustment value
1 - 99
50
RRCB-MFT
(Lead edge adjustment:
registration motor ON
timing) manual feed
adjustment value
registration motor ON
timing) manual feed
adjustment value
1 - 99
50
RRCB-
CS12
CS12
(Lead edge adjustment:
registration motor ON
timing) tray 1 adjustment
value
registration motor ON
timing) tray 1 adjustment
value
1 - 99
50
RRCB-
CS34
CS34
(Lead edge adjustment:
registration motor ON
timing) desk adjustment
value
registration motor ON
timing) desk adjustment
value
1 - 99
50
Print off
center
adjust-
ment
center
adjust-
ment
RRCB-ADU
(Lead edge adjustment:
registration motor ON
timing) ADU adjustment
value
registration motor ON
timing) ADU adjustment
value
1 - 99
50
RRCB-LC
(Lead edge adjustment:
registration motor ON
timing) LCC/LCT
adjustment value
registration motor ON
timing) LCC/LCT
adjustment value
1 - 99
50
RRCB-
ADU-HV-A
ADU-HV-A
(Lead edge adjustment:
registration motor ON
timing) ADU adjustment
value (Heavy paper A)
registration motor ON
timing) ADU adjustment
value (Heavy paper A)
1 - 99
50
RRCB-CS-
HV-A
HV-A
(Lead edge adjustment:
registration motor ON
timing) main unit tray
adjustment value (Heavy
paper A)
registration motor ON
timing) main unit tray
adjustment value (Heavy
paper A)
1 - 99
50
RRCB-CS-
HV-OHP
HV-OHP
(Lead edge adjustment:
registration motor ON
timing) main unit tray
adjustment value (OHP)
registration motor ON
timing) main unit tray
adjustment value (OHP)
1 - 99
50
RRCB-LC-
HV-A
HV-A
(Lead edge adjustment:
registration motor ON
timing) LCC/LCT
adjustment value (Heavy
paper A)
registration motor ON
timing) LCC/LCT
adjustment value (Heavy
paper A)
1 - 99
50
RRCB-LC-
HV-B
HV-B
(Lead edge adjustment:
registration motor ON
timing) LCC/LCT
adjustment value (Heavy
paper B)
registration motor ON
timing) LCC/LCT
adjustment value (Heavy
paper B)
1 - 99
50
RRCB-MFT-
HV-A
HV-A
(Lead edge adjustment:
registration motor ON
timing) manual feed tray
adjustment value (Heavy
paper A)
registration motor ON
timing) manual feed tray
adjustment value (Heavy
paper A)
1 - 99
50
RRCB-MFT-
HV-B
HV-B
(Lead edge adjustment:
registration motor ON
timing) manual feed tray
adjustment value (Heavy
paper B)
registration motor ON
timing) manual feed tray
adjustment value (Heavy
paper B)
1 - 99
50
RRCB-MFT-
HV-OHP
HV-OHP
(Lead edge adjustment:
registration motor ON
timing) manual feed tray
adjustment value (OHP)
registration motor ON
timing) manual feed tray
adjustment value (OHP)
1 - 99
50
RRCB-MFT-
HV-ENV
HV-ENV
(Lead edge adjustment:
registration motor ON
timing) manual feed tray
adjustment value
(Envelope)
registration motor ON
timing) manual feed tray
adjustment value
(Envelope)
1 - 99
50
MULTI
COUNT
COUNT
Number of print
1 - 999
1
PAPER
Tray selection
1 - 9
2
DUPLEX
Duplex print selection
0 - 1
1
Item/Display
Content
Setting
range
Default
value
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man24) service manuals if exist.