Read Sharp MX-6240N / MX-7040N (serv.man17) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 63
9-D
(14)
DSPF mode (Copy/Scan/FAX) density
adjustment (No need to adjust normally)
DSPF mode (Copy/Scan/FAX) density
adjustment (No need to adjust normally)
This setting is normally not required, however, in the following
cases, make changes to the setting:
* When copy in DSPF mode differs from copy in document table
cases, make changes to the setting:
* When copy in DSPF mode differs from copy in document table
mode.
* When copy density in DSPF mode is low or too high.
* When the DSPF unit is replaced.
* When the DSPF unit is disassembled.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
* When the DSPF unit is replaced.
* When the DSPF unit is disassembled.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
a. Adjustment procedure
1) Enter the SIM 46-9 mode.
1) Enter the SIM 46-9 mode.
2) Select the mode to be adjusted with the scroll key.
When adjusting density on low density part, select "A (COPY
LOW)". When adjusting density on high density part, select "D
(COPY HIGH)".
LOW)". When adjusting density on high density part, select "D
(COPY HIGH)".
3)
Enter the adjustment value with 10-key.
In case of increase of image density, input large numeric
value. Or in case of diluting the image density, input small
numeric value.
In case of increase of image density, input large numeric
value. Or in case of diluting the image density, input small
numeric value.
4)
Press [OK] key.
5)
Make a copy in the DSPF mode and check the copy.
If a satisfactory result is not obtained, return to the SIM 46-9 mode
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
9-D
(15)
Automatic color balance adjustment by the
user (Copy color balance automatic
adjustment ENABLE setting and
adjustment)
Automatic color balance adjustment by the
user (Copy color balance automatic
adjustment ENABLE setting and
adjustment)
a. General
In the user program mode, the user can execute the auto color cal-
ibration (auto adjustment of the copy color balance and density).
This adjustment is to set Enable/Disable of the above user opera-
tion with SIM 26-53.
In the user program mode, the user can execute the auto color cal-
ibration (auto adjustment of the copy color balance and density).
This adjustment is to set Enable/Disable of the above user opera-
tion with SIM 26-53.
CAUTION: This setting must be set to ENABLE only when the
user's understanding on the automatic adjustment of
the copy color balance and density and the user's oper-
ational ability are judged adequate enough to execute
the adjustment.
When set to enable, operation procedures must be fully
explained to the user.
the copy color balance and density and the user's oper-
ational ability are judged adequate enough to execute
the adjustment.
When set to enable, operation procedures must be fully
explained to the user.
Item
Button
Display
Content
Setting
range
Default
value
A
OC
COPY
SIDEA:
LOW
SIDEA:
LOW
DSPF copy mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
B
SCAN
SIDEA:
LOW
SIDEA:
LOW
DSPF scanner mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
C
FAX SIDEA:
LOW
LOW
DSPF FAX mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
ǂǂǂ6,08/$7,21ǂǂ12
7(67
&/26(
˖&23<6,'($/2:
˖6&$16,'($/2:
˖)$;6,'($/2:
˖&23<6,'($+,*+
˖6&$16,'($+,*+
˖)$;6,'($+,*+
(;32685($'-8670(1763)
$
˷̚˹
$˖
%˖
&˖
'˖
(˖
)˖
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
%$&.
0212
&2/25
(;,7
&/($5
2.
2&
'63)
ǂǂǂ6,08/$7,21ǂǂ12
7(67
&/26(
˖&23<6,'(%/2:
˖6&$16,'(%/2:
˖)$;6,'(%/2:
˖&23<6,'(%+,*+
˖6&$16,'(%+,*+
˖)$;6,'(%+,*+
˖%$/$1&(6,'(%5
˖%$/$1&(6,'(%*
˖%$/$1&(6,'(%%
(;32685($'-8670(1763)
$
˷̚˹
$˖
%˖
&˖
'˖
(˖
)˖
*˖
+˖
,˖
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
.(<
%$&.
0212
&2/25
(;,7
&/($5
2.
2&
'63)
OK
10-key
'63)
D
OC
COPY
SIDEA:
HIGH
SIDEA:
HIGH
DSPF copy mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
52
E
SCAN
SIDEA:
HIGH
SIDEA:
HIGH
DSPF scanner mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
52
F
FAX SIDEA:
HIGH
HIGH
DSPF FAX mode
exposure adjustment
(High density)
exposure adjustment
(High density)
1 - 99
52
A
DSPF
COPY
SIDEB:
LOW
SIDEB:
LOW
DSPF copy mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
B
SCAN
SIDEB:
LOW
SIDEB:
LOW
DSPF scanner mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
C
FAX SIDEB:
LOW
LOW
DSPF FAX mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
D
COPY
SIDEB:
HIGH
SIDEB:
HIGH
DSPF copy mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
50
E
SCAN
SIDEB:
HIGH
SIDEB:
HIGH
DSPF scanner mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
50
F
FAX SIDEB:
HIGH
HIGH
DSPF FAX mode
exposure adjustment
(High density)
exposure adjustment
(High density)
1 - 99
50
G
BALANCE
SIDEB: R
SIDEB: R
DSPF color balance
R
R
1 - 99
50
H
BALANCE
SIDEB: G
SIDEB: G
DSPF color balance
G
G
1 - 99
50
I
BALANCE
SIDEB: B
SIDEB: B
DSPF color balance
B
B
1 - 99
50
Item
Button
Display
Content
Setting
range
Default
value
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man17) service manuals if exist.