Read Sharp MX-6240N / MX-7040N (serv.man17) Service Manual online
MX-7040N ADJUSTMENTS AND SETTINGS 5 – 62
2) Select the item A, B with the scroll key.
* If a tone gap occurs on part of high density, set 0 to item A and B
The density of high density part decreases. However, the tone
gap is better.
gap is better.
* In case of more increase of the density on high density part, set 1
to item A and B.
The tone gap may occur in high density part.
The tone gap may occur in high density part.
CAUTION: Do not change the setting values of item C, D, E and F.
If these values are changed, density of the high density
part is changed.
If these values are changed, be sure to execute the
copy color balance density adjustment. (Auto adjust-
ment)
part is changed.
If these values are changed, be sure to execute the
copy color balance density adjustment. (Auto adjust-
ment)
9-D
(13)
Copy color balance adjustment
(Single color copy mode)
(No need to adjust normally)
Copy color balance adjustment
(Single color copy mode)
(No need to adjust normally)
This adjustment is used to set the color balance and the density in
the single color copy mode to the user's request.
The adjustment is made by changing Y, M, C components of each
color.
This adjustment is not required normally, but executed when there
is a request from the user.
When the default adjustment value is changed, this adjustment is
required in the following cases.
* When it is required to change the color balance in the single
the single color copy mode to the user's request.
The adjustment is made by changing Y, M, C components of each
color.
This adjustment is not required normally, but executed when there
is a request from the user.
When the default adjustment value is changed, this adjustment is
required in the following cases.
* When it is required to change the color balance in the single
color copy mode.
* When there is request from the user.
a. Adjustment procedure
1)
1)
Enter the SIM 46-25 mode.
2)
Select the color to be adjusted with the scroll key.
3)
Select the color (YMC) to be adjusted with the color key.
4)
Enter the adjustment value with 10-key.
5)
Press [OK] key.
6)
Make a copy in the single color copy mode and check the
copy.
copy.
If a satisfactory result is not obtained, return to the SIM 46-25 mode
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
Display/Item
Content
Setting
range
Default
A
CMY
(0:ENABLE
1:DISABLE)
(0:ENABLE
1:DISABLE)
0
CMY engine maximum
density correction mode
Enable
density correction mode
Enable
0 - 1
0
1
CMY engine maximum
density correction mode
Disable
density correction mode
Disable
B
K
(0: ENABLE
1: DISABLE)
(0: ENABLE
1: DISABLE)
0
K engine maximum density
correction mode Enable
correction mode Enable
0 - 1
1
1
K engine maximum density
correction mode DIsable
correction mode DIsable
C
CYAN MAX
TARGET
TARGET
Scanner target value for CYAN
maximum density correction
maximum density correction
0 - 999
500
D
MAGENTA
MAX TARGET
MAX TARGET
Scanner target value for
MAGENTA maximum density
correction
MAGENTA maximum density
correction
0 - 999
500
E
YELLOW
MAX TARGET
MAX TARGET
Scanner target value for
YELLOW maximum density
correction
YELLOW maximum density
correction
0 - 999
500
F
BLACK MAX
TARGET
TARGET
Scanner target value for
BLACK maximum density
correction
BLACK maximum density
correction
0 - 999
500
Display/Item
Adjustment range
Default
C
M
Y
A
RED
0 - 255
0
255
200
B
GREEN
0 - 255
255
0
255
C
BLUE
0 - 255
255
200
0
D
YELLOW
0 - 255
0
0
255
E
MAGENTA
0 - 255
0
255
0
F
CYAN
0 - 255
255
0
0
OK
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,1*/(&2/2502'(&2/25%$/$1&(6(783
$˖
˷̚˹
˖5('
$˖
˖*5((1
%˖
˖%/8(
&˖
˖&<$1
'˖
˖<(//2:
)˖
˖0$*(17$
(˖
2.
&
0
<
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
6,1*/(&2/2502'(&2/25%$/$1&(6(783
$˖
˷̚˹
˖5('
$˖
˖*5((1
%˖
˖%/8(
&˖
˖&<$1
'˖
˖<(//2:
)˖
˖0$*(17$
(˖
2.
&
0
<
Click on the first or last page to see other MX-6240N / MX-7040N (serv.man17) service manuals if exist.