Read Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) Service Manual online
MX-4101N SIMULATION 6 – 5
41
1
Used to check the operations of the document size sensor and the control circuit.
2
Used to adjust the document size sensor detection level.
3
Used to check the operations of the document size sensor and the control circuit.
43
1
Used to set the fusing temperature in each mode.
4
Used to set the fusing temperature 2 in each mode. (Continued from SIM 43-1.)
20
Used to set the environmental correction under low temperature and low humidity (L/L) for the fusing
temperature setting (SIM 43-1) in each paper mode.
temperature setting (SIM 43-1) in each paper mode.
21
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing
temperature setting (SIM 43-1) in each paper mode.
temperature setting (SIM 43-1) in each paper mode.
22
Used to set the environment correction under low temperature and low humidity (L/L) for the fusing
temperature setting (SIM 43-4) in each paper mode.
temperature setting (SIM 43-4) in each paper mode.
23
Used to set the environment correction under high temperature and high humidity (H/H) for the fusing
temperature setting (SIM 43-4) in each paper mode.
temperature setting (SIM 43-4) in each paper mode.
24
Used to set the correction of the temperature adjustment value of SIM 43-1 and 43-4.
31
Used to check the operation of the fusing web cleaning motor.
Fusing
32
Used to set various items related to the forcible operation of web cleaning when job end.
Fusing
44
1
Used to set each correction operation function in the image forming (process) section.
Image process (Photoconductor/
Developing/Transfer/Cleaning)
Developing/Transfer/Cleaning)
2
Used to adjust the sensitivity of the image density sensor (registration sensor).
Process
4
Used to set the conditions of the high density process control operation.
Process
6
Used to execute the high density process control forcibly.
Process
9
Used to display the result data of the high density process control operation.
Image process (Photoconductor/
Developing/Transfer/Cleaning)
Developing/Transfer/Cleaning)
12
Used to display the operation data of the high density process control and the image density sensor
(registration sensor).
(registration sensor).
Image process
(Photoconductor/Developing)
(Photoconductor/Developing)
13
Used to perform the color image sensor (image registration sensor F) calibration.
14
Used to display the output level of the temperature and humidity sensor.
Process (OPC drum, development)/
Fusing/LSU
Fusing/LSU
16
Used to display the toner density control data.
Developing system
21
Used to set the half tone process control target.
Process
22
Used to display the toner patch density level in the half tone process control operation.
Process
24
Used to display the correction target and the correction level in the half tone process control operation.
Process
25
Used to set the calculating conditions of the correction value for the half tone process control.
Process
26
Used to execute the half tone process control compulsorily.
Process
27
Used to clear the correction data of the half tone process control.
Process
28
Used to set the process control execution conditions.
Process
29
Used to set the operating conditions of the process control during a job.
Process
31
Used to adjust the OPC drum phase. (Manual adjustment)
Process
37
Used to set the development bias correction level in the continuous printing operation.
43
Used to display the identification information of the developing unit.
Developing system
61
Used to adjust the color image density sensor. (The adjustment is made according to the input of SIM44-
13 to set the target value of the color sensor gain adjustment.)
13 to set the target value of the color sensor gain adjustment.)
46
1
Used to adjust the copy density in the copy mode.
2
Used to adjust the copy density in the copy mode.
4
Used to adjust the density in the image send mode.
5
Used to adjust the density in the image send mode.
8
Used to adjust the image send mode color balance RGB.
9
Used to adjust the scan image density.
10
Used to adjust the copy color balance and the gamma (for each color copy mode).
16
Used to adjust the monochrome copy density and the gamma (for each monochrome copy mode).
19
Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode
documents.
documents.
21
Copy color balance adjustment (Manual adjustment)
23
Used to set the density correction of copy high density section (High density tone gap supported).
24
Copy color balance adjustment (Auto adjustment)
25
Used to adjust the copy color balance. (Single color copy mode)
26
Used to reset the single color mode color balance set value to the default.
27
Used to adjust the gamma/density of copy images, texts, and line image edges.
30
Used to adjust the resolution in the sub scanning direction in the copy mode.
32
Used to adjust the document background density reproducibility in the monochrome auto copy mode.
36
Used to adjust the colors in the 2-color copy mode.
37
Used to adjust the color document reproducibility in the monochrome copy mode.
38
Used to adjust the black component amount in the color copy mode.
39
Used to adjust the sharpness of FAX send images.
40
Used to adjust the FAX send image density. (Collective adjustment of all the modes)
Main
Sub
Functions
Section
Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) service manuals if exist.