MX-4100N, MX-4101N, MX-5000N, MX-5001N (serv.man14). Service Manual-Section 6-Simulations - Sharp Copying Equipment Service Manual (repair manual). Page 6

Read Sharp MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) Service Manual online

MX-4101N  SIMULATION  6 – 6
46
41
Used to adjust the FAX send image density. (Normal)
42
Used to adjust the FAX send image density. (Fine)
43
Used to adjust the FAX send image density. (Super Fine)
44
Used to adjust the FAX send image density. (Ultra fine)
45
Used to adjust the FAX send image density. (600dpi).
47
Used to set the compression rate of copy and scan images (JPEG).
51
Used to adjust the gamma for the copy mode heavy paper mode and the image process mode.
52
Used to set the gamma default for the copy mode heavy paper and the image process mode. 
(The set values of SIM46-51 are set to the default values.)
54
Used to perform the engine half tone automatic density adjustment (dither). 
60
Used to adjust the sharpness in the color auto copy mode.
61
Used to adjust the area separation recognition level.
62
Used to set the operating conditions of the ACS, the area separation, the background image process, and 
the auto exposure mode.
63
Used to adjust the density in the copy low density section.
74
Copy color balance adjustment (Auto adjustment)/
Printer color balance adjustment (Auto adjustment)
90
Used to adjust the high compression PDF ASIC.
48
1
Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning 
direction).
5
Used to correction the scan image magnification ratio (in the sub scanning direction).
Scanner section
6
Used to adjust the rotation speed of each motor.
49
1
Used to perform the firmware update.
3
Used to update the operation manual in the HDD.
5
Used to perform the watermark update.
50
1
Copy image position, image loss adjustment
2
Used to adjust the copy image position and the image loss. (This simulation is a simplified version of SIM 
50-1).
5
Used to adjust the print lead edge image position. (PRINTER MODE)
6
Used to adjust the copy image position and the image loss. (RSPF/DSPF mode)
RSPF/DSPF
7
Used to adjust the copy image position and the image loss (RSPF/DSPF mode). 
(This simulation is a simplified version of SIM 50-6.)
RSPF/DSPF
10
Used to adjust the black print image magnification ratio and the off-center position. 
(The adjustment is made separately for each paper feed section.)
12
Used to perform the scan image off-center position adjustment. 
(The adjustment is made separately for each scan mode.)
20
Image registration adjustment (Main scanning direction) (Manual adjustment)
21
Image registration adjustment (Sub scanning direction) (Manual adjustment)
22
Used to adjust the image registration. (Main scan direction, sub scan direction) 
(Auto adjustment)/OPC drum phase adjustment (Auto adjustment)
24
Used to display the detail data of SIM 44-2, 50-20, 21 and 22.
27
Used to perform the image loss adjustment of scanned images in the FAX or image send mode.
28
Used to automatically adjust the image loss, void area, image off-center, and image magnification ratio.
51
1
Used to adjust the ON/OFF timing of the secondary transport voltage.
2
Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF/DSPF 
resist roller. (This adjustment is performed when there is a considerable variation in the print image 
position on the paper or when paper jams frequently occur.)
53
6
Used to adjust the detection level of the RSPF/DSPF document width.
7
Used to adjust the RSPF/DSPF document size width sensor.
8
Used to adjust the document lead edge reference and the RSPF/DSPF mode document scan position.
55
1
Used to set the specifications of the engine control operations. (SOFT SW)
2
Used to set the specifications of the scanner control operation. (SOFT SW)
3
Used to set the specifications of the controller operation. (SOFT SW)
56
1
Used to transport data between HDD - MFP PWB SRAM/EEPROM. (Used to repair the PWB.)
2
Used to backup the data in the EEPROM. SRAM, and HDD (including user authentication data and 
address data) to the USB memory. (Corresponding to the device cloning and the storage backup.)
3
Used to backup the document filing data to the USB memory.
4
Used to backup the JOB log data to the USB memory.
60
1
Used to check the operations (read/write) of the MFP PWB image memory (SDRAM).
2
Used to set the MFP PWB onboard SDRAM.
61
1
Used to check the LSU polygon motor rotation and laser detection.
LSU
3
Used to set the laser power 
4
Used to print the print image skew adjustment pattern. (LSU unit)
Main
Sub
Functions
Section
Page of 127
Display

Click on the first or last page to see other MX-4100N / MX-4101N / MX-5000N / MX-5001N (serv.man14) service manuals if exist.