MX-4100N, MX-4101N, MX-5000N, MX-5001N (serv.man13). Service Manual-Section 5-Adjustments - Sharp Copying Equipment Service Manual (repair manual). Page 4

MX-4101N  ADJUSTMENTS  5 – 4

 

This adjustment is needed in the following situations:
* The developing unit has been disassembled.
* When the print image density is low.
* When there is a blur on the print image.
* When there is unevenness in the print image density.
* The toner is excessively dispersed.
1)

Remove the developing doctor cover, and place the develop-
ing unit on a flat surface.

2)

Attach a piece of string to a sewing needle or pin.

3)

Hold the thread and bring the needle near the developing
roller. (Do not use a paper clip because too heavy. It will not
provide a correct position.)

4)

Mark the developing roller surface on the extension line of the
needle with the needle at 2 - 3mm from the developing roller
surface. (Never touch the needle tip with the developing roller.)

5)

Measure the distance between the marking position and posi-
tion A of the developing unit frame, and check that it is 37.8 

±

0.5mm.
If the distance is not within the above range, adjust the devel-
oping roller main pole position in the following procedures.

6)

Remove the developing unit front cover, loosen the fixing
screw of the developing roller main pole adjustment plate, and
move the adjustment plate in the arrow direction to adjust.

Repeat procedures 3) - 6) until the developing roller main pole
position comes to the specified range.

7)

After completion of the adjustment of the developing roller
main pole position, fix the developing roller main pole adjust-
ment plate with the fixing screw.

 

This adjustment is needed in the following situations:
* When developer is replaced.

NOTE: Be sure to execute this adjustment only when developer is

replaced. Never execute it in the other cases.

1)

With the front cabinet open, enter SIM25-2.

2)

Close the front cabinet.

3)

Select a developing unit to be adjusted.

㨪3mm

EXECUTE

M

K

Adjustment completed

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

$7'(9($'-B/B.

$7'(9(92B0B.

$7'(9($'-B/B&

$7'(9(92B0B&

$7'(9($'-B/B0

$7'(9(92B0B0

$7'(9($'-B/B<

$7'(9(92B0B<

$7'(9($'-B0B.

$7'(9($'-B0B&

$7'(9($'-B0B0

$7'(9($'-B0B<

$7'(9(92B/B.

$7'(9(92B/B&

$7'(9(92B/B0

$7'(9(92B/B<

.

&

0

<

Abnormal end

ǂǂǂ6,08/$7,21ǂǂ12

&/26(

7(67

$8720$7,&'(9(/23(5$'-8670(17

(;(&87(

7&'B.(((/

7&'B&

7&'B0(((/

7&'B<

7&9B.(((/

7&9B&(((/

7&9B0(((/

7&9B<(((/

.

&

0

<