Read Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man9) Service Manual online
MX3500N SIMULATION 7 – 14
<Inner finisher (MX-FNX1)>
<4K finisher>
<4K saddle finisher>
[Screen (Saddle finisher (MX-FNX2) installed)]
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray and the related circuit.
ity tray and the related circuit.
Section
Desk/Large capacity tray (LCC)
Item
Operation
Operation/Procedure
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
<A4 LCC sensor>
<A3 LCC sensor>
J
PUNCH HOLE
Punch hole position
adjustment
adjustment
0 to 100
50
Item
Display
Item
Set range
Default
value
A
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
2 to 18
10
B
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
2 to 18
10
C
STAPLE REAR
Staple binding position
adjustment (one
position at the rear)
adjustment (one
position at the rear)
68 to 132
100
D
STAPLE FRONT
Staple binding position
adjustment (one
position in front)
adjustment (one
position in front)
68 to 132
100
E
STAPLE BOTH
Staple binding position
adjustment (two
positions at the
center)
adjustment (two
positions at the
center)
68 to 132
100
F
STAPLE PITCH
Staple binding position
adjustment (two
positions in pitch)
adjustment (two
positions in pitch)
68 to 132
100
G
PUNCH
CENTER
CENTER
Punch center
adjustment
adjustment
37 to 63
50
H
PUNCH HOLE
Punch hole position
adjustment
adjustment
42 to 58
50
Item
Display
Item
Set range
Default
value
A
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 to 20
10
B
STAPLE REAR
Staple binding position
adjustment (one
position at the rear)
adjustment (one
position at the rear)
94 to 106
100
C
STAPLE FRONT
Staple binding position
adjustment (one
position in front)
adjustment (one
position in front)
94 to 106
100
D
PUNCH
CENTER
CENTER
Punch center
adjustment
adjustment
40 to 60
50
E
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 to 52
50
Item
Display
Item
Set range
Default
value
A
SADDLE
POSITOIN
POSITOIN
Saddle binding
position adjustment
position adjustment
197 to 203
200
B
FOLDING
POSITION
POSITION
Saddle folding
position adjustment
position adjustment
192 to 208
200
C
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 to 20
10
D
STAPLE REAR
Staple binding position
adjustment (one
position at the rear)
adjustment (one
position at the rear)
94 to 106
100
E
STAPLE FRONT
Staple binding position
adjustment (one
position in front)
adjustment (one
position in front)
94 to 106
100
F
PUNCH
CENTER
CENTER
Punch center
adjustment
adjustment
40 to 60
50
G
PUNCH HOLE
Punch hole position
adjustment
adjustment
46 to 52
50
Item
Display
Item
Set range
Default
value
DCSI1
Desk 1 installation detection
DPFD1
Desk 1 transport detection
DLUD1
Desk 1 upper limit detection
DPED1
Desk 1 paper empty detection
DCSPD1
Desk 1 remaining paper quantity detection
DCSS11
Desk 1 rear edge detection 1
DCSS12
Desk 1 rear edge detection 2
DCSS13
Desk 1 rear edge detection 3
DCSS14
Desk 1 rear edge detection 4
DCSI2
Desk 2 instillation detection
DPFD2
Desk 2 transport detection
DLUD2
Desk 2 upper limit detection
DPED2
Desk 2 paper empty detection
DCSPD2
Desk 2 remaining paper quantity detection
DCSS21
Desk 2 rear edge detection 1
DCSS22
Desk 2 rear edge detection 2
DCSS23
Desk 2 rear edge detection 3
DCSS24
Desk 2 rear edge detection 4
DSW_DSK
Desk transport cover open/close detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit sensor
LDD
LCC tray lower limit sensor
LPED
LCC tray paper empty sensor
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder sensor
L24VM
LCC 24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit sensor
LDD
LCC tray lower limit sensor
LPED
LCC tray paper empty sensor
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder sensor
0
A:
A
㧦200
B
㧦200
C
㧦 10
D
㧦 10
㧧 SADDLE POSITION
㧧 FOLDING POSITION
㧧 FRONT ADJUSUT
㧧 REAR ADJUSUT
SIMULATION
NO.03-10
FINISHER
ADJUSTMENT
200
㨇 0 㨪400 㨉
OK
TEST
CLOSE
Click on the first or last page to see other MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man9) service manuals if exist.