Read Sharp MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man118) Technical Bulletin online
Sharp Electronics (UK) Ltd., Technical Services Group
CCE-346/363/378/428/441
4. Upgrade 8
From December 2006 production
ROM
control No.
ICU
(PROGRAM)
ICU
(BOOT)
PCU
SCU
DSPF
IMAGE
DATA
FAX
D23
0206J0
* 0206J0
0113J0
0111J0
0111J0
0101J0
010400
*ICU BOOT above is the version described in the ROM management label. Check that
the actual version is:
the actual version is:
*ICU (BOOT): 01.00.00/LANGUAGE: 01.42.00/GRAPHIC: 01.04.00 (Sim22-5).
Item of change: See below
No.
Subject
Description
1
EFI Option
Support for MX-PEX2 of EFI printer controller has been provided. When installing MX-
PEX2, please update to this version.
PEX2, please update to this version.
2
EFI Option
Following item of NIC page has been corrected;
printer name MX-PEX1
MX-PEX2
Following item of Sim22-10 has been corrected;
printer name MX-PEX1
MX-PEX2
3
Supply
An improvement of the overtoner (Toner Leakage) when Heavy Paper is selected at low
speed mode has been made.
speed mode has been made.
4
Improvement of the
noise
noise
For Low-noise to be possible, modification has been made not to activate the cooling fan
of MFPC and HDD even if the accumulated time of the fan stop is over 30 minutes during
the Power Save Mode.
of MFPC and HDD even if the accumulated time of the fan stop is over 30 minutes during
the Power Save Mode.
5
Correction of the
Paper Jam
Paper Jam
When starting the print from PC while the main unit was in the preheat mode on the
system with Saddle Finisher, the PPD2_S1 jam occurred depending on the print timing.
This glitch has been corrected.
system with Saddle Finisher, the PPD2_S1 jam occurred depending on the print timing.
This glitch has been corrected.
The firmware for the Saddle Finisher also needs to be changed to Ver.01.04.00 or later
version.
version.
6
Copy
Modification "(No.23) Change of magnification with N-up and Border-Off" that has been
made on T/R No.CCE-363R was also reflected on the copy jobs with the card scan
function. This problem has been corrected.
made on T/R No.CCE-363R was also reflected on the copy jobs with the card scan
function. This problem has been corrected.
7
Printer
Modification has been made to record that it is N-up in to the job log when selecting N-up
on the print job (PCL/PS).
on the print job (PCL/PS).
8
Printer
The problem that the printer hung up when printing multiple copies with duplex on to the
paper types such as the printed paper and letterhead etc without using "Print per Unit"
has been corrected.
paper types such as the printed paper and letterhead etc without using "Print per Unit"
has been corrected.
9
Scan to E-mail
If the "Custom" was selected as the server type on the Web Page when LDAP
authentication was enabled, not the e-mail address of log-in user but the SMTP reply
mail address was adopted as the Reply Mail Address. This problem has been corrected.
authentication was enabled, not the e-mail address of log-in user but the SMTP reply
mail address was adopted as the Reply Mail Address. This problem has been corrected.
10
Scan to E-mail
If the line feed code was included when entering the Body Text of the Scan to E-mail, the
network communication error occurred, and e-mail could not be sent out. This problem
has been corrected. The problem does not arise on the mail server that LF of the line
code is supported.
network communication error occurred, and e-mail could not be sent out. This problem
has been corrected. The problem does not arise on the mail server that LF of the line
code is supported.
11
Firmware Update
We announced in S/I No.CCE-381 that there were some cases where the back light of
LCD panel was not turned ON after start-up of the main unit, which caused the reboot
failure of the main unit when upgrading the firmware via USB, FTP or WEB Page, and
also the workaround for this case was provided. The correction has been made to reboot
the machine without failure. However this correction will be available after upgrading to
this version or later because the machine works with the new firmware after the reboot.
LCD panel was not turned ON after start-up of the main unit, which caused the reboot
failure of the main unit when upgrading the firmware via USB, FTP or WEB Page, and
also the workaround for this case was provided. The correction has been made to reboot
the machine without failure. However this correction will be available after upgrading to
this version or later because the machine works with the new firmware after the reboot.
Click on the first or last page to see other MX-3500N / MX-3501N / MX-4500N / MX-4501N (serv.man118) service manuals if exist.