Read Sharp MX-2630 (serv.man6) Handy Guide online
SHARP
REPAIR HINTS
MX-2630N Handy Guide NOV’17
Sharp Office Solutions Group
Page 73
/75
OUTPUT FINISHER
Query
Is it possible to increase the number of sets in
the saddle stitch tray when printing booklets
(if the saddle tray is removed, the Saddle
Finisher will still ask to empty the tray after 10
sets (approx.)
the saddle stitch tray when printing booklets
(if the saddle tray is removed, the Saddle
Finisher will still ask to empty the tray after 10
sets (approx.)
Advice
You cannot increase the number of sets to the
saddle tray however, if you drop the backstop
down on the saddle tray, the discharged paper
will fall off the tray and therefore the tray will
never show full.
saddle tray however, if you drop the backstop
down on the saddle tray, the discharged paper
will fall off the tray and therefore the tray will
never show full.
MX-FN29
Remove a screw on back side
of the Saddle tray and remove
the stopper on the rear edge.
Remove a screw on back side
of the Saddle tray and remove
the stopper on the rear edge.
MX-FN31
Pull the knob at the base of
the stopper on the saddle tray
end towards you and then
lower
Pull the knob at the base of
the stopper on the saddle tray
end towards you and then
lower
Query
Staple/Fold position is incorrect
Advice
First (ignoring the current fold & staple
positions), adjust the Fold position so it
matches the current staple position using DIP
Switch SW100 on the Finisher Control PWB:-
positions), adjust the Fold position so it
matches the current staple position using DIP
Switch SW100 on the Finisher Control PWB:-
Then using System settings - Common settings
- Device control - Saddle Fold/Stitch Position
Adjustment menu, adjust the staple/fold
position centrally. Once the fold position is
correct, loosen the blue screw and adjust any
skew by turning the knurled screw at the
bottom of the saddle unit.
- Device control - Saddle Fold/Stitch Position
Adjustment menu, adjust the staple/fold
position centrally. Once the fold position is
correct, loosen the blue screw and adjust any
skew by turning the knurled screw at the
bottom of the saddle unit.
Note: The Staple & Fold positions for Saddle
Stitch can be independently adjusted using
SIM3-10:-
(CJ = Saddle Stitch, CK = Saddle Fold
Stitch can be independently adjusted using
SIM3-10:-
(CJ = Saddle Stitch, CK = Saddle Fold
).
SHARP PRINT RELEASE
Query
Which models can be configured to use Sharp
Print Release?
Print Release?
Advice
Sharp Print Release is supported on
MX-2630N -MX6070N series, MX-6580/7580N
& MX-M905 only.
MX-2630N -MX6070N series, MX-6580/7580N
& MX-M905 only.
Query
When using Sharp Print Release, what is the
recommended number of client MFPs that can
be connected to the MFP Master?
recommended number of client MFPs that can
be connected to the MFP Master?
Advice
It is recommended that up to 5 client MFPs can
be connected to a single MFP master.
be connected to a single MFP master.
PRINTER
Query
Unable to perform Office Direct Print - docx,
xlsx & pptx files are not listed when browsing
USB memory or FTP/SMB server.
xlsx & pptx files are not listed when browsing
USB memory or FTP/SMB server.
Advice
To perform Office Direct Print, the optional
MX-PU10 must be installed.
MX-PU10 must be installed.
Query
After upgrading from Windows 8 to 8.1 / 10 or
Server 2012 to 2012R2, “Features”
information on the printer properties is not
displayed.
Server 2012 to 2012R2, “Features”
information on the printer properties is not
displayed.
Advice
This is caused by the OS upgrade. If you change
the Printer Name or change/reset the Port
properties of the queue, the Features
information will return.
the Printer Name or change/reset the Port
properties of the queue, the Features
information will return.
SHARP OSA
Query
Configuring Sharp OSA - Standard Application
& External Accounting Application settings.
& External Accounting Application settings.
Advice
For Sharp OSA v5.1 supported devices, there
are some new settings available that has
affected the configuration of both Standard
Application Settings (MX-AMX2) and External
Accounting Application Settings (MX-AMX3).
Unless otherwise stated by the Solution
Vendor, the Browser Setting should be set to
HTML Browser 3.5 and the Data Size should be
set to Wide-SVGA.
Note: MX-AMX2 or MX-AMX3 are required.
are some new settings available that has
affected the configuration of both Standard
Application Settings (MX-AMX2) and External
Accounting Application Settings (MX-AMX3).
Unless otherwise stated by the Solution
Vendor, the Browser Setting should be set to
HTML Browser 3.5 and the Data Size should be
set to Wide-SVGA.
Note: MX-AMX2 or MX-AMX3 are required.
Adjuster (Knurled)
Screw
Click on the first or last page to see other MX-2630 (serv.man6) service manuals if exist.