Read Sharp MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man9) Service Manual online
MX-2300/2700 N/G SIMULATION 7 – 12
3-10
Purpose
Adjustment
Function (Purpose) Used to adjust the finisher.
Section
Section
Finisher
Item
Operation
Operation/Procedure
1) Select the item according to the adjustment content with [
1) Select the item according to the adjustment content with [
↑] [↓]
buttons.
2) Enter the adjustment value with 10-key.
3) Press [OK] button. (The set value is saved.)
<Saddle finisher>
3) Press [OK] button. (The set value is saved.)
<Saddle finisher>
<Inner finisher>
[Screen (Saddle finisher installed)]
4
4-2
Purpose
Operation test/check
Function (Purpose) Used to check the operations of the sen-
sors and detectors in the desk/large capac-
ity tray and the related circuit.
ity tray and the related circuit.
Section
Desk/Large capacity tray (LCC)
Item
Operation
Operation/Procedure
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
<Desk sensor>
<A4 LCC sensor>
Item
Display
Item
Set
range
Default
value
A
SADDLE POSITION
Saddle binding
position adjustment
position adjustment
0 to 400
200
B
FOLDING POSITION
Saddle folding
position adjustment
position adjustment
0 to 400
200
C
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
0 to 20
10
D
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
0 to 20
10
E
STAPLE REAR
Staple binding
position adjustment
(one position at the
rear)
position adjustment
(one position at the
rear)
0 to 200
100
F
STAPLE FRONT
Staple binding
position adjustment
(one position in front)
position adjustment
(one position in front)
0 to 200
100
G
STAPLE BOTH
Staple binding
position adjustment
(two positions at the
center)
position adjustment
(two positions at the
center)
0 to 200
100
H
STAPLE PITCH
Staple binding
position adjustment
(two positions in
pitch)
position adjustment
(two positions in
pitch)
0 to 100
50
I
PUNCH CENTER
Punch center
adjustment
adjustment
47 to 53
50
J
PUNCH HOLE
Punch hole position
adjustment
adjustment
0 to 100
50
Item
Display
Item
Set
range
Default
value
A
FRONT ADJUST
Alignment position
adjustment (front)
adjustment (front)
2 to 18
10
B
REAR ADJUST
Alignment position
adjustment (rear)
adjustment (rear)
2 to 18
10
C
STAPLE REAR
Staple binding position
adjustment (one
position at the rear)
adjustment (one
position at the rear)
68 to 132
100
D
STAPLE FRONT
Staple binding position
adjustment (one
position in front)
adjustment (one
position in front)
68 to 132
100
E
STAPLE BOTH
Staple binding position
adjustment (two
positions at the
center)
adjustment (two
positions at the
center)
68 to 132
100
0
SIMULATION NO.03̆03
TEST
FIN LOAD CHECK
EXECUTE
FINRPS
FJPM
FJFM
FFM
FPM
FAM
FFJM
FRJM
FSM
FFSM
FLM
FFC
CLOSE
1/1
1/1
F
STAPLE PITCH
Staple binding position
adjustment (two
positions in pitch)
adjustment (two
positions in pitch)
68 to 132
100
G
PUNCH CENTER
Punch center
adjustment
adjustment
37 to 63
50
H
PUNCH HOLE
Punch hole position
adjustment
adjustment
42 to 58
50
DCSI1
Desk 1 installation detection
DPFD1
Desk 1 transport detection
DLUD1
Desk 1 upper limit detection
DPED1
Desk 1 paper empty detection
DCSPD1
Desk 1 remaining paper quantity detection
DCSS11
Desk 1 rear edge detection 1
DCSS12
Desk 1 rear edge detection 2
DCSS13
Desk 1 rear edge detection 3
DCSS14
Desk 1 rear edge detection 4
DCSI2
Desk 2 instillation detection
DPFD2
Desk 2 transport detection
DLUD2
Desk 2 upper limit detection
DPED2
Desk 2 paper empty detection
DCSPD2
Desk 2 remaining paper quantity detection
DCSS21
Desk 2 rear edge detection 1
DCSS22
Desk 2 rear edge detection 2
DCSS23
Desk 2 rear edge detection 3
DCSS24
Desk 2 rear edge detection 4
DSW_DSK
Desk transport cover open/close detection
LPFD
LCC transport sensor
LUD
LCC tray upper limit sensor
LDD
LCC tray lower limit sensor
LPED
LCC tray paper empty sensor
LCD
LCC tray insertion detection
LDSW
LCC upper open/close detection SW
LRE
LCC lift motor encoder sensor
L24VM
LCC24V power monitor
LLSW
LCC upper limit SW
LTOD
LCC main unit connection detection
Item
Display
Item
Set
range
Default
value
0
A:
A㧦200
B㧦200
C㧦 10
D㧦 10
㧧
SADDLE POSITION
㧧
FOLDING POSITION
㧧
FRONT ADJUSUT
㧧
REAR ADJUSUT
SIMULATION NO.03-10
FINISHER ADJUSTMENT
200
㨇
0 㨪400 㨉
OK
TEST
CLOSE
Click on the first or last page to see other MX-2300N / MX-2700N / MX-2300G / MX-2700G / MX-2300FG / MX-2700FG (serv.man9) service manuals if exist.